Resume - Thirty years experience of Construction, Startup & Commissioning, Operations & T...

Misco Jobs

Resume #3042

CONTACT INFORMATION:
View contact information...

Professional Experience

04/03-Present    COMBINED CYCLE CONTROL ROOM SUPERVISOR
SNC Lavalin / NES Overseas Ltd.
Gila River Power Project, 2150 Mw, 4 Block Two-on-One Combined Cycle Units, GE 7FA Gas Turbines, Alstom HRSGs with Duct Burners and SCR, GE D11 Steam Turbines, Westinghouse Ovation DCS.
Gila Bend, AZ
-    Provided Control Room supervision and coordinated activities of Operation’s staff from Steam Blows through Commercial Operation.
-    Tested/verified DCS control algorithms and provided tuning input, alarm setpoint verification.

04/02- 4/03    COMBINED CYCLE SITE STARTUP MANAGER
Kiewit Industrial Corporation
High Desert Power Project, Three-on-One Combined Cycle Unit, Siemens Westinghouse 501FD Gas Turbines, ABB HRSGs with Duct Burners and SCR, Toshiba Steam Turbine, Westinghouse Ovation DCS, US Filter Zero Liquid Discharge and Aquifer Banking Water Treatment
Victorville, CA
-    Supervised and coordinated activities of the Startup staff.
-    Developed Primavera Critical Path Method schedule for Pre-operational Testing and Initial Startup and Operation phases.
-    Identified Startup Staff Manload requirements and hired appropriate staff.
-    Responsible for Startup staff budget including craft and staff labor, subcontracts and materials.
-    Set Walkdown Standards to verify unit built to technical specifications.
-    Developed Requests for Quotations for Startup subcontracts.
-    Prepared System Scoping and Start-up Packages, package content requirements and supervised development and completion of the packages.
-    Developed System Startup Workplans for component and system checkout and integrated operations.
-    Developed and implemented Construction Work List and Owner Punchlist Tracking Program.
-    Implemented Startup Administrative Procedures including System Engineer Training.
-    Established Cross Reference database for all EPC deliverables to appropriate turnover documentation .
-    Implemented Lockout Tagout Procedures and developed Startup Work Permit Procedure.
-    Developed Preventative Maintenance Program.
-    Developed procedures and methods for compliance with California Energy Commission requirements.
-    Issued Warranty Claims to Vendors.
-    Established Door, Panel and Equipment Key control and turnover, including index generation
-    Established Startup Spares identification requirements, ordering and tracking.
-    Established Vendor Rep Scheduling, Owner notification, Service Reports, Filing system.
-     Developed Facility Demonstration and Performance Tests.

01/02- 04/02    COMBINED CYLE HRSG COMMISSIONING CONSULTANT
Duke Flour Daniel / Aalborg, Inc. / PIC
Bastrop Energy Center, Two-on-One 535 Mw Combined Cycle Unit, GE 7FA Gas Turbines, Aalborg Duct fired HRSGs, Mitsubishi Steam Turbine
Bastrop, Texas
-    Provided oversight of installation, commissioning, and start-up processes for the HRSGs and their auxiliaries.
-    Performed Erection Mechanical Completion walkdowns.
-    Pre-identified all potential expansion issues.
-    Monitored HRSG performance during steam blows and full load operation.
-    Performed post Steam Blow gas path inspections and problem identification.
-    Established final system setpoints.
-    Provided Operator classroom HRSG fundamentals and operations training.
-    Resolved all Warranty issues.
-    Assisted Duke Flour Daniel with integrated plant operational issue resolution.

11/00-11/01    COMBINED CYCLE LEAD MECHANICAL COMMISSIONING ENGINEER
        OCM GANTT
James A. Vann, Jr. Power Plant, Two-on-One 500 Mw Combined Cycle Unit, Siemens Westinghouse 501FD Combustion Gas Turbines, NEM HRSGs, Mitsubishi Steam Turbine
        Gantt, Alabama
-    Responsible for verification / completion of the 501FD Installation and Commissioning record books.
-    Develop and implement routine preventative maintenance program.
-    Review P&ID's and engineering documents (data sheets, etc.)
-    Develop/Implement Mechanical Startup and Test Program.
-    Supervise/assign work to Mechanical Technicians and construction crafts.
-    Interface with constructor, owner and vendors to support testing activities.
-    Review / Finalize complete System Turnover Packages.
-    Perform system walkdowns and prepare punchlists, coordinate punch list completion activities.
-    Conduct and direct cleaning, flushing and commissioning of all mechanical systems
-    Correct Mechanical problems within start-up Scope of Work.
-    Work with client and O&M staff in support of start-up testing and on-the-job-training.
-    Prepared and maintained Mechanical portion of all System Turnover Package and as-builts.
-    Resolve basic and detail technical and engineering mechanical and control design problems
-    Prepared and administrated Safety and Clearance Tagging Procedure
-    Prepared a complete listing of all air system isolation valves and the components affected by their shutoff
-    Prepared Gas Blow Procedure and maintained total site control and supervision during gas blows

11/00-3/01    COMBINED CYCLE STARTUP MANAGER
        OCM GANTT
        James A. Vann, Jr. Power Plant, Two-on-One 500 Mw Combined Cycle Unit
        Gantt, Alabama
-    Prepared Start-up Package List, package content requirements and supervised development and completion of the packages
-    Implemented OWDL (Outstanding Work & Deficiencies List) Tracking Program
-    Established Cross Reference database for all EPC requirements to appropriate turnover documentation
-    Issued Warranty Claims to Vendors
-    Established Door, Panel and Equipment Key control and turnover, including index generation
-    Established/Participated in Critical Path Method scheduling for Pre-operational Testing and Initial Startup and Operation phases
-    Established Borrowing of Spare Parts and replenishment
-    Established Vendor Rep Scheduling, Owner notification, Service Reports, Filing
-    Determine/Implement Startup’s role in Development, Review and Approval of Acceptance Test Procedures, Operations Manuals including Systems Descriptions and Integrated Facility Operating Instructions

8/99-11/00    COAL PLANT LEAD MECHANICAL COMMISSIONING ENGINEER
        Black & Veatch International
        Paiton Power Station Phase II, Coal Fired 2 x 610Mw (Siemens, ABB, BVI consortium)
        Paiton, Indonesia
-    Perform erection completion inspections, pre-startup equipment checks, integrated startup, testing and optimization of this prototype standard
-    Resolve basic and detail technical and engineering mechanical and control design problems
-    Technical interface between Client and Consortium Partners
-    Technical issue tracking and expediting
-    Turnover Package documentation completion
-    Senior Authorized Person to establish isolation measures for designated systems
-    Prepare and maintain Mechanical portion of all System Turnover Package and as-builts.
-    Implement routine preventative maintenance program.
-    Supervise/assign work to Mechanical Technicians and construction crafts.

1/99-8/99    ICS-24 HRSG COMMISSIONING MANAGER
        ABB HRSG Group
        Berkshire Power Station
        Agawam, MA
-    Develop Commissioning Inspection and Testing Plan
-    Develop all Cold and Hot Commissioning procedures for equipment, integrated checkout and the performance test
-    Perform erection completion inspections, pre-startup equipment checks, integrated startup and testing, and final performance evaluations of the HRSG and its accessories
-    Provide Quality Assurance of Owners Turnover Package records during commissioning
-    Assist Erection Advisor in resolution of construction, erection and engineering problems for this prototype Next Generation HRSG
-    Assist in Product Line Development

5/96 – 12/98    INSTRUMENTATION & CONTROL LEAD TECHNICAL CONSULTANT
ABB-CEII, ABB Combustion Engineering International, Inc.
Ulchin Nuclear Generating Station 3&4
Ulchin, Korea
- Technical Advisor to the Startup and Permanent Plant I&C Departments during construction, construction acceptance testing, pre-operational testing, cold hydro, hot functional testing, and power ascension testing.
- Assist in NSSS system initial startup, checkout, and calibration including Modicon PLC’s, Foxboro Micro Spec 200 control and process instrumentation, ABB-CE Protection and Control systems
- Assist in BOP system initial startup, checkout, and calibration including all Radwaste systems, Eaton Plms 32 Plant Control system, Eagle & Allen-Bradley PLC’s, Primary and Secondary Sampling system, Turbine-generator auxiliaries
- Provide training and assistance in Protective System Pressure Ramp Response time testing, RTD response time testing, and Reactor Protection System Channel response time testing
-    Provide extensive interface with overseas vendors for problem resolution of I&C, Electrical, and Mechanical systems
- Engineer corrections and field implement design deficiencies
- Provide configuration control and startup troubleshooting of Radiation Monitoring System computers, software and OS/2 operating system
- Assist in troubleshooting Plant Monitoring System (Plant Computer)
- Setup, train and troubleshoot Concurrent Temporary Data Acquisition System

12/93 - 5/96    OPERATIONS LEAD TECHNICAL CONSULTANT
Combustion Engineering International, Inc.
Yonggwang Nuclear Generating Station 3&4
Yonggwang, Korea
- Technical Advisor to Operations, I&C, Electrical, and Mechanical Departments during construction, construction acceptance testing, pre-operational testing, cold hydro, hot functional testing, power ascension testing, and commercial operation.
- Performed system walkdown and inspections during all phases
- Performed Test Working Group technical review of I&C, Electrical, and Mechanical System preoperational tests and test results
- Prepared Operations Hot Functional and Power Ascension Test Procedures
- Developed the NSSS and Turbine-Generator Warranty Test Procedures
- Performed Plant Nuclear Safety Committee technical review of power ascension test procedures and results
- Prepared Operation’s test procedure test summaries and test reports
- Worked extensively with I&C Department to resolve problems on NSSS and BOP I&C systems
- Worked extensively with GE Technical Advisor to resolve all Turbine-Generator Operational issues and startup problems
-    Interfaced with overseas vendors for problem resolution of I&C, Electrical, and Mechanical systems
- Prepared scheduling for testing phases and work outages for the units
- Assisted in performance, calculations and data analysis of the NSSS and Turbine-Generator Warranty tests

11/89 - 12/92    LICENSED SENIOR REACTOR OPERATOR TRAINING CONSULTANT
Arizona Public Service Company
Palo Verde Nuclear Generating Station
Wintersburg, Arizona
- Qualified classroom and training instructor for Initial License and Requalification Programs in all areas (I&C, Electrical and Mechanical)
- Developed and prepared classroom and simulator training program materials for Reactor Operator, Requalification, and Shift Technical Advisor
- Performed Senior Reactor Operator, Reactor Operator Task Analysis
- Delivered Initial License, Requalification, Shift Technical Advisor classroom and simulator training programs
- Developed Initial License and Requalification Program Exambanks
- Administered annual Requalification examinations and provided Requalification upgrade training

11/86 - 11/89    SENIOR REACTOR OPERATOR SIMULATOR PROGRAM DEVELOPER
Florida Power and Light Company
St. Lucie Nuclear Generating Company
Port St. Lucie, Florida
- Performed Senior Reactor Operator/Reactor Operator Task Analysis
- Developed Simulator training program for Reactor Operator, Senior Reactor Operator, Requalification and Shift Technical Advisors
- Developed Simulator Evaluation program and Job Performance Measures in accordance with NUREG 1021
- Upgraded all classroom and simulator training materials to incorporate procedure changes, plant modifications and industry lessons learned
- Delivered Shift Technical Advisor Training
- Developed software code for an automated exambank

3/83 - 11/86    LICENSE TRAINING INSTRUCTOR
Arizona Public Service Company
Palo Verde Nuclear Generating Station
Wintersburg, Arizona
- Developed and prepared Initial License training program materials in accordance with INPO accreditation criteria
- Delivered Initial License classroom training including NSSS & BOP Instrumentation and Control Systems, Mitigating Core Damage, and Transient Accident Analysis
- Developed and delivered training course in GE Mark III Analog Turbine Generator Control and Support Systems
- Administered annual site Requalification License Examinations

1/83 - 3/83    SIMULATOR ACCEPTANCE TESTER
Combustion Engineering
Windsor, Connecticut
- Performed acceptance test procedures and validation checkout of Calvert Cliffs simulator under construction
- Analyzed simulator performance for correct operational/theoretical response, direct interface with programmers/engineers and Fortran 77 code to determine the hardware/software deficiencies

2/81 - 11/82    SENIOR REACTOR OPERATOR
Illinois Power Company
Clinton Nuclear Power Station
Clinton, Illinois
- Performed/supported initial startup and testing of I&C, Electrical and Mechanical systems during construction, startup and turnover phases of this BWR 6
- Directed on-shift activities of reactor operators, plant equipment operators and test engineers
- Developed plant operational, surveillance and test procedures for I&C systems
- Performed technical review and audit of I&C startup procedures

2/80 - 2/81    COMPUTER/FIELD SERVICES ENGINEER
Bandag, Inc.
Muscatine, Iowa
- Installed and setup industrial testing computers at dealers nationwide
- Provided initial and continuing training on computer operation
- Performed computer troubleshooting and repair
- Performed I&C maintenance and calibration
- Performed electrical and mechanical repair of AC and DC drive equipment

10/78 - 2/80    ELECTRONIC ANALYST
Motorola, Inc.
Mt. Pleasant, Iowa
- Performed setup, calibration, troubleshooting and repair of manufactured electronics equipment
- Performed Root Cause Analysis on electronic component failure
- Provided initial and continuing training to forty electronic technicians

11/72 - 10/78    ENGINEERING WATCH SUPERVISOR / REACTOR OPERATOR
U.S. Navy
- Supervised I&C, Electrical and Mechanical Equipment Operators during overhaul, testing, and operational phases of a submarine PWR plant at sea and in overhaul
- Lead engineer in charge of I&C equipment operation, calibration, maintenance and repair
- Directed training and requalification of Reactor Operations Department

Accreditation’s
- PVNGS Senior Reactor Operator Certification
- NRC PWR Senior Reactor Operator, Docket No. 55-60176
- Clinton Power Station BWR 6 Senior Reactor Operator
- Navy- Reactor Operator, Nuclear Engineering, Radio Electronics Technician, Radar Electronics Technician, Advanced Electronics, Industrial Management and Supervision, Supervisory Skills for Industrial Managers

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 701 to 750 of 2516)

Go to Search Parameters...

Brief Description

25 years Experience Materials & Logistics, Base Manager, UK, West Africa, Middle East

Contracts, Services Manager, Wellhead Maintenace, Integrity Engineer, Senior Well Engineer

15yrs In the Indian Navy as a Hydrographic Surveyor, served onboard various Indian Naval Surveying Ships and four years as a Hydrographic Surveyor with Fugro India Pvt Ltd worked on various survey ships and offshore construction Barges in oil and gas field.

Free! I come with17 yrs exp in the technical, operational and management aspects of Well Completions in the Oil & Gas industry. I am interested in rewarding and challenging opportunities as a Completions / Well Services / Well Test Consultant where I can contribute from my wealth of experience.

EHS Management Expert with 14+ years of Experience

I am 42 years old and Master Degree, currently I am still working for Valeinco as Logistic Manager and I ahave many experiences in Project Management such as Contract Services Manager, Project Manager and Project Coordinator and with my experiences I am confidence to be one of your candidate/staff.

Well Test and C&WI services, i.e., Coiled tubing, acidizing, sand control, wireline, Fracturing, cementing, well testing, slickline, e-line, perforation programs, down hole plugs, x-mas tree change outs, and other.

GRAUDATE.AND DIPLOMA HOLDER IN INDUSTRIAL SAFETY MANAGEMENT AND ALSO HAVE 6 YEARS 4 MONTHS EXPERIENCE.

20 years of HR experience in recruitment, remuneration, pay structure development, performance management, job evaluation, benefits, organizational design, employee relations, database management, leadership, management, facilitation, coordination

I have over 36 years in the Oil & Gas Industry. International experience on land & offshore. Experience in remote location logistics. Have worked in desert, mountains, & jungle. Have drilled HTHP wells with oil base mud. Experience drilling horizontal & underbalanced. Spanish Speaking.

OBJECTIVE: Seeking full time employment with some reputed company in order to be able to play a major role in its activities and enhance my skills alike.

Reliability, maintainability & logistics, welding inspector, Mechanical engineer

Offshore Maintenance Supervisor FPSO Experience, Heavy Oil Experience

Certification as a machinist, supervisor, Engineer, & licensed teacher + 25 years in 16 countries. machine service centers (GE, Sulzer), supervise overseas workshops (Badak LNG), start-up & commissioning, chemical plants field supervisor (Dow, Mobay) trouble shooter (Brown & Root, GE),

29 years experience in Quantity Surveying, Commercial and Contracts Management in the oil & gas, nuclear and petrochemical industries. Experience in all aspects of pre-contract engineering and post-contract administration under various contracting strategies and formats.

I’m interested in a Marketing Communications Director position. With over thirty years of experience, I can bring a high level of creativity as well as the ability to initiate and take small or large projects / events from concept to execution while managing all stages of the development.

I have over twenty years experience in procuring, coordinating and delivering all logistical equipment needed for drilling, construction and production for oil/gas and natural gas operations. Extensive experience in J.I.B. Exceptional ability in the skill of negotiating

Under balanced Drilling, UB Drilling, Air Drilling, OHSE Management, Operations Manager Drilling Consultant, Tool pusher

Result oriented Chemical Engineering Professional with a Post graduation in Management offering extensive experience of over 14 years in the Commercial and Government Market place. A broad experience base, with a proven record of success in Industrial projects

Drilling Fluids Cementing Logistics Marketing Management

14 years experience in Electrical Controls/Instrumentation field. PLC programming, Variable frequency drives, AutoCad, Electrical Codes, Industrial networks ProfiBus, DH+, DeviceNet

A Chemical Engineer with outstanding professional experience of more than 30 years in the manufacturing / Projects/Process engineering and HSE management in Petrochemical / Chemical/Fertilizer plants /Offsite and terminal complex.

13 yrs AWS CWI QA & QC inspection & management, industrial construction in major plant expansions & combined cycle power plants.

Started as Drilling Engineer. Project management expertise. Contract document prep & specs. Procurement of products/services/consultancy ,management of contractors/suppliers. Responsible for commercial, logistical, technical performance of jobs. Tendering, contract negotiations. Budgets up to £10m.

I am at present a Tool Pusher in Chad. IWCF Surface BOP Stack ; Current through 3/06 H2S Alive Certificate, Saudi Arabia Exxon Leadership Safety Training Workshop Eddie Bauer Problem Solving Certificate S.C.R. Rosehill Prodico Certificate

Objective: To obtain a management or Business Development position with a Service Company in the Oil Industry that will allow me to implement my engineering and management knowledge in Completions and Production

22 years of experience in the oil field trucks, cranes, forklifts, loaders, pickup's, passenger cars.

Safety Manager Seeking Position

Supervisory/Management position in a corporation promoting quality, team effort and excellent customer/worker relations. 20+ years supervising labourers, welders, & fitters on many different jobs and locations. Oil, Gas, Petroleum, & Pipelines. Many trips to Iraq in the 80's

Expediting Manager with 40 plus intermediate and senior Expeditor's with experience ranging from 250M - 5.6B Oil & Gas Projects.

Strategic Planning Business Development Project and Business Valuation

I have BSc. in Mechanical Engineering, MSc. in Mechanical Vibration of Rotating and MSc. in design of gas turbines. I have >20years of experience with Engineering and Operating Companies in O&G and Petrochemical fields as Senior Mechanical Engineer in Egypt Enppi and in Qatar QP Offshore and QVC

32 years Oil Industy experience in Drilling Fluids / waste Manging / Cementing / Drilling Engineering / Business Develeopment / Project Management. Degree. experience of Cpld weatehr, HTHO, deep water, H2S wells.

Perhaps you are looking for an experienced Security, Surveillance and Investigations Management professional, who is highly skilled in all aspects of highly sensitive investigations, corporate security, surveillance and asset protection?

Field Manager/ Operations Supt. with experience managing international oil/gas projects.

Inspection high pressure vessels and supervision pipe-lines in Europe. Quality Assurance & Quality Control in nuclear power plant - crew 7 people. Quality Control, punching, hydro-testing of pipe systems - crew 10 persons.

I am a driven and focused individual who knows how to set goals and work to achieve them. Outstanding skills/competencies in Materials Management, Inventory Control and Accounting. Pro-active and results-oriented with the talent for identifying and solving problems.

Over twenty-four years of professional experience as a planner, scheduler, estimator, project engineer and supervisor in the industrial construction, maintenance and turnaround fields of the petrochemical, paper and pulp, power generating textile manufacturing and offshore industrial industries.

Proven ability in Purchasing, Expediting, Procurement QA/QC Coordinator, Material Control, Material Coordinator, Logistics and Warehousing. Developed and implemented Material Control and Warehouse Procedures. Proficient in SAP, MS Word and Excel. Bilingual, fluent in English and conversational Thai.

Over 30 years of experience in refineries as craftsman, mid-level supervisor. Since taking early retirement from Chevron in California, I have taken positions mainly as client field construction QA representative on projects of millions of USD's. Also worked as DBA D.J.A. Consulting.

RESIDENT CONSTRUCTION MANAGER / SUBCONTRACTS MANAGER / CONSULTANT IN CONSTRUCTION OF PETROCHEMICAL PLANTS (SPECIFICALLY HYDROGEN /SYNGAS REFORMERS, ETHYLENE CRACKING FURNACES, PETROCHEMICAL UNITS INCLUDING DETAIL PLANNING AND EXECUTION OF SEVERAL PLANT TURNAROUNDS PROJECTS)

PROFESSIONAL OBJECTIVES Senior Drilling Engineer- Drilling Superintendent Houston / Overseas Assignments and Rotation Wide range of drilling experience in Well Planning / Engineering and Operations / Offshore and Onshore / Domestic and International.

Thirty years experience of Construction, Startup & Commissioning, Operations & Training for Combined Cycle Units, Coal Fired and Nuclear Steam Supply Systems (NSSS) & Balance of Plant (BOP) Systems.

Please see my attached Resume. As you will see I have a wide range of experience in Valves, Controls, Regulators, Rotating Equipment.

Mathematics BS.C English Arabic bilingual Experience in large civil and oil-gas projects. Logistic, accounting, environmental and general supervision.

My strength is in rig management and in particular jack-up rigs in the international market. In excess of twenty years diversified experience in execution and management of drilling and workover operations worldwide onshore and offshore operations.

MBA with comprehensive experience in oil and gas industry; strong skills in project management and business development; good communicator and outstanding interpersonal and leadership skills; Canadian citizenship

I am a Commissioning \ Construction \ Hook Up Manager with 27 years experience in the Oil, Gas and Power Industries.

Operation rig manager for drilling rigs onshore and offshore.

A Professional Engineer with more than 27 years oil & gas experience. P. Eng Status current

First 1 2 3 4 5 6 7 8 9 10 11 12 13 14 [ 15 ] 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Next Last

Seach Parameters


Change search parameters...
CATEGORIES: Management; INDUSTRIES: Petroleum/Oil/Gas;
Change search parameters...
Keywords: (e.g. mining engineer)		Find results with:


Save this search parameters...
Post job with this search parameters...

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out