CONTACT INFORMATION:
View contact information...
Position: Instrumentation QA/QC Inspector/Supervisor
Educational Attainment:
1- Apprenticeship in Industrial Instrumentation & Process Control
In 1997 From NFC Institute IET Multan.
2-F.SC (Pre-Engineering) Session 1993-1995
Permanent Address:
Basti Rahim Shah
P.O.BOX & Tehsil Jahanian District Khanewal
PAKISTAN
Nationality: Pakistani
Date Of Birth: 02/22/1976
Marital Status: Married
Training Seminars / Workshop Attended:
* ISO 9001-2000 TRAINING
* SAP TRAINING
* COMPASS TRAINING
Employment Records:
1)Company PETRO- RABIGH
A Joint Venture Company By Sumitomo
Chemical co.Ltd.(Japan) & Saudi Arabian Oil Co.
(Saudi Aramco)
Location Saudi Arabia
Position INSTRUMENTATION QA/QC INSPECTOR/SUPERVISOR
Inclusive Date March 28, 2007 To Up to date.
DUTIES & RESPONSIBILITIES
Review plans and drawings in accordance with specifications, codes and standards. Familiar with the International industry codes and standards related to intrinsically safe systems and electrical systems for Instrumentation such as; NFPA 70/NEC, NEMA 250, NEMA VE 1, NEMA VE 2,NEMA ICS 6, UL94, IEC 60529,IEEE518, IEEE1100, ANSI MC 96.1, ISA RP12.6, ISA RP 12.2.02
* Conduct activities and inspection in accordance to Project Quality Assurance Manual and Quality Control Inspection Plan.
* Monitor daily discipline activities and verifies compliance to project procedures, specifications and standards. Identify quality problems, reject non-conforming items and initiate, recommend or provide solutions to the problems with customer sanction / approvals through designated channels.
* As Per International & Saudi Aramco Standards, Specifications, Instrument Calibration Method of Statement & As Per Approved Project Drawings Supervised, Inspected & Witnessed calibration workshop,DCS Cabinets frame insideRIB'S, Instrument Cable Duct Bank, Cable Pulling from RIB to J.B & Control Room and RGS conduit, Stanchion of instrument devices, Marshalling Panel, Junction Boxes installation, Mounting of instrument devices.
* Anything not as per Standards or Specification then Making Surveillance or Non Conformance Reports
* Carried out daily job activities after receiving RFI(Request for inspection) from contractor
2)Company Jubail United Petrochemical Co.(JUPC)
by Sabic and Flour Danial
Location Saudi Arabia
Position INSTRUMENT INSPECTOR
Inclusive Date April 21, 2004 To December 05, 2006
DUTIES & RESPONSIBILITIES
* Review plans and drawings in accordance with specifications, codes and standards. Conduct activities and inspection in accordance to Project Quality Assurance Manual and Quality Control Inspection Plan. Monitor daily discipline activities and verifies compliance to project procedures, specifications and standards. Identify quality problems, reject non-conforming items and initiate, recommend or provide solutions to the problems with customer sanction / approvals through designated channels. Control further processing of non-conforming items, deficiencies or unsatisfactory conditions until rectification and any remedial action is approved. Conduct random surveillance on operator's qualifications, tools and equipment, working practices as well as storage and preservations. Prepare daily inspection documents and final acceptance documents prior to project completion. Maintain close working relationship with the construction personnel.
* As Per Sabic Standards, Specifications, Instrument Calibration Method of Statement & As Per Approved Project Drawings Supervised, Inspected & Witnessed Instrument Cable Duct Bank, Cable Pulling from RIB to J.B & Control Room and RGS conduit, Stanchion of instrument devices, Marshalling Panel, Junction Boxes installation, Mounting of instrument devices such as pressure, level, temperature transmitter, RTD and thermocouple, pressure, Level, Flow and temperature switch & Control valves. Calibration of Transmitters, Control valves, Switches of all Parameters Like pressure, Level, temperature, Flow
* Involved in FAT(Factory acceptance test) & SAT(Site acceptance test) Activities
* Inspection & Witness of cable megger & continuity test before Terminating Cable & then Cable Termination Check to verify exact termination point of each cable core as per Approved wiring Drawing, Core Marker & tightness of cable
* Anything not as per Standards or Specification then Making Surveillance or Non Conformance Reports
* Carried out daily job activities after receiving RFI(Request for inspection) from contractor
* Work for loop checking, Interlock check, P & ID, ILD, Data Sheet
* Prepared Punch list for the activities carried out by construction group
* Work on Pre & Final turnover punching System
* Inspection of Instrument Calibration Shop, Test equipment as per SABIC Standard
3)COMPANY Millac Foods Private Limited
Pakistan
POSITION INSTRUMENT SUPERVIOSR
INCLUSIVE DATE NOV 30,2002 ~ Apri10, 2004
Duties & Responsibilities:
Supervise field construction project related to instrumentation. Responsible for the preparation of instrument, take off material and drawing needed in the project. Installation of cable tray, conduit, ImpulseTubing and Instrument air line. Responsible for Installation & calibration of instrument, loop-checking, megger and continuity testing of cable. Supervise termination of primary/secondary cable and PLC panel and junction box.
4) COMPANY Jubail Petrochemical company Kemya
(Joint Venture of Sabic & Exxon)
LOCATION Saudi Arabia
POSITION INSTRUMENT QA/QC INSPECTOR
INCLUSIVE DATE August 18, 2000 To August 25, 2002
:
DUTIES & RESPONSIBILITIES
* Witnessed Calibration of instrument like pressure, level, temperature, pressure switch, temperature switch control valves I/P converters, limit switch solenoid valves.
* Inspection of cable tray installation and conduit, Fabricated support of instrument devices and electrical equipments alignment of panel, marshalling box, mounting of instrument devices such as pressure, level, temperature transmitter, RTD and thermocouple pressure switch and temperature switch. Cable pulling from control room to J.B then from J.B to Field Instruments.
* Supervise termination of instrument Cable in junction box, marshalling panel
* Impulse line test pressure
* Assist in plant commissioning works, loop checking, Interlock check, P & ID, ILD, and punch list works
* Preparation of Loop folders
* Modification jobs
5) Company: PAK-AMERICAN FERTILIZERS LTD. (TOYO ENGG. PROJECT)
Position: INSTRUMENT QA/QC INSPECTOR
Inclusive Date: OCT 02, 1997 ~ AUGUST 15, 2000
I WORKED AS QA/QC INSPECTOR & INSTRUMENT TECHNICIAN IN ERRECTION,COMMISSIONING,START-UP AND MAINTENANCE
AT PAK-AMMERICAN FERTILIZER LIMITED PAKISTAN
PAK AMMERICAN FERTILIZER LTD. IT IS ONE OF THE PIONEER FERTILIZER UNITS OF NFC.INITIALLY IN THIS UNIT AMMONIUM SULPHATE WAS PRODUCED. LATER ON IT STARTED A MODERNIZATION & EXPANSION PROJECT OF 600/1050 MTPD AMMONIA /UREA (A PROJECT OF M/S TOYO ENGINEERING CORPORATION OF JAPAN).THE KELLOG/ACES PROCESS HAVING LATES TOTAL DISTRIBUTION CONTROL SYSTEM (TDC3000-X) WHICH CONTAINS APM FOR HIGH LEVEL CALCULATION & ADVANCED CONTROL STRATEGIES.LM FOR INTERLOCKING.HM FOR SYSTEM DATA STORAGE, PROCESS HISTORY,GPRAPHIC DISPLAY,AND CONFIGURATION INFORMATION.THE PLANT IS ALSO EQUIPED WITH HI-TECH CENTRIFUGAL COMPRESSORS WITH LATEST PROGRAMED ELECTRONICS GOVERNING CONTROL SYSTEM FOR EXTRACTION/CONDENSING TURBINES WITH COMPLETE INTERLOCKING FOR SAFE OPERATION
Duties & Responsibilities:
* CALIBRATION & MAINTENANCE OF ALL TYPE OF ELECTRONIC & PNEUMATIC INSTRUMENTS.
* REPAIR & MAINTAIN ALL TYPE OF PRESSURE, LEVEL, FLOW, TEMP. ETC.SMART TRANSMITTERS
* WORKING EXPERIENCE ON DIFFERENT MANUFACTURER'S TRANSMITTERS LIKE HONEYWELL,ROSEMOUNT,FISHER, YOKOGAWA & FOXBORO ETC
* WORKED ON ULTRASONIC FLOWMETER XMT868(PANAMETRICS)
* WORKED ON MAGNETIC FLOWMETER OF YOKOGAWA MODEL AE 100,200 & 300
* WORKED ON VORTEX FLOWMETER MODEL DY,DYA OF YOKOGAWA
* WORKED ON MICROMOTION(EMERSON) FLOW TRANSMITTERS
* RADAR TYPE LEVEL TRANSMITTER (VEGAPULSE 56K,44,42)
* WORK ONCONTROL VALVES OF NELES,MASONEILAN,FISHER,VALTEK
* WORKED ON FIELDVUE DVC 6000 SERIES DIGITAL VALVE CONTROLLER(FISHER)
* CHECK & CALIBRATE MOTORIZED VALVE(LIMITORQUE & ROTORK)
* CALIBRATION & MAINTENANCE OF THERMOCOUPLE & RTD'S
* CALIBRATE PRESSURE,LEVEL & TEMPERATURE SWITCHES
* CALIBRATE PRESSURE & TEMPERATURE GAUGES
* INTERNAL LOOP CHECK OF DI, AI, AO POINTS IN CONTROL ROOM
* TROUBLE SHOOTING OF VIBRATION MONITORING SYSTEM OF TURBINE & COMPRESSOR (BENTLY & NEVADA 3300,3500, 7200)
* CHECK INTERLOCKING
* TROUBLE SHOOTING, FAULT FINDING ON PROGRAMMABLE LOGIC CONTROLLER (PLC)& PESS(PROGRAMMABLE ELECTRONIC SAFETY SYSTEM)
* TROUBLING SHOOTING & FAULT FINDING EXPERIENCE ON DCS e.g. TDC 3000X HONEYWELL & YOKOGAWA CENTUM CS 3000
* LOOP TEST OF ALL KINDS OF ELECTRONIC & PNEUMATIC CONTROL LOOPS.
* CARRIED OUT PREVENTIVE MAINTENANCE JOB AS PER PROCEDURES
* TO MAKE CHANGES IN MAINTENANCE PROCEDURES & WORK INSTRUCTION
View contact information... |