Resume - Power Generation- Twenty-eight years experience of Construction, Startup & Commi...

Misco Jobs

Resume #2546

CONTACT INFORMATION:
View contact information...

Professional Experience

04/02-Present COMBINED CYCLE SITE STARTUP MANAGER
Kiewit Industrial Corporation
High Desert Power Project, Three-on-One Combined Cycle Unit, Siemens Westinghouse 501FD Gas Turbines, ABB HRSGs with Duct Burners and SCR, Toshiba Steam Turbine, Westinghouse Ovation DCS, US Filter Zero Liquid Discharge and Aquifer Banking Water Treatment
Victorville, CA
- Supervised and coordinated activities of the Startup staff.
- Developed Primavera Critical Path Method schedule for Pre-operational Testing and Initial Startup and Operation phases.
- Identified Startup Staff Manload requirements and hired appropriate staff.
- Responsible for Startup staff budget including craft and staff labor, subcontracts and materials.
- Set Walkdown Standards to verify unit built to technical specifications.
- Developed Requests for Quotations for Startup subcontracts.
- Prepared System Scoping and Start-up Packages, package content requirements and supervised development and completion of the packages.
- Developed System Startup Workplans for component and system checkout and integrated operations.
- Developed and implemented Construction Work List and Owner Punchlist Tracking Program.
- Implemented Startup Administrative Procedures including System Engineer Training.
- Established Cross Reference database for all EPC deliverables to appropriate turnover documentation.
- Implemented Lockout Tagout Procedures and developed Startup Work Permit Procedure.
- Developed Preventative Maintenance Program.
- Developed procedures and methods for compliance with California Energy Commission requirements.
- Issued Warranty Claims to Vendors.
- Established Door, Panel and Equipment Key control and turnover, including index generation
- Established Startup Spares identification requirements, ordering and tracking.
- Established Vendor Rep Scheduling, Owner notification, Service Reports, Filing system.
- Developed Facility Demonstration and Performance Tests.

01/02- 04/02 COMBINED CYLE HRSG COMMISSIONING CONSULTANT
Aalborg, Inc. / PIC
Bastrop Energy Center, Two-on-One 535 Mw Combined Cycle Unit, GE 7FA Gas Turbines, Aalborg Duct fired HRSGs, Mitsubishi Steam Turbine
Bastrop, Texas
- Provided oversight of installation, commissioning, and start-up processes for the HRSGs and their auxiliaries.
- Performed Erection Mechanical Completion walkdowns.
- Pre-identified all potential expansion issues.
- Monitored HRSG performance during steam blows and full load operation.
- Performed post Steam Blow gas path inspections and problem identification.
- Established final system setpoints.
- Provided Operator classroom HRSG fundamentals and operations training.
- Resolved all Warranty issues.
- Assisted Duke Flour Daniel with integrated plant operational issue resolution.

11/00-11/01 COMBINED CYCLE LEAD MECHANICAL COMMISSIONING ENGINEER
OCM GANTT
James A. Vann, Jr. Power Plant, Two-on-One 500 Mw Combined Cycle Unit, Siemens Westinghouse 501FD Combustion Gas Turbines, NEM HRSGs, Mitsubishi Steam Turbine
Gantt, Alabama
- Responsible for verification / completion of the 501FD Installation and Commissioning record books.
- Develop and implement routine preventative maintenance program.
- Review P&ID's and engineering documents (data sheets, etc.)
- Develop/Implement Mechanical Startup and Test Program.
- Supervise/assign work to Mechanical Technicians and construction crafts.
- Interface with constructor, owner and vendors to support testing activities.
- Review / Finalize complete System Turnover Packages.
- Perform system walkdowns and prepare punchlists, coordinate punch list completion activities.
- Conduct and direct cleaning, flushing and commissioning of all mechanical systems
- Correct Mechanical problems within start-up Scope of Work.
- Work with client and O&M staff in support of start-up testing and on-the-job-training.
- Prepared and maintained Mechanical portion of all System Turnover Package and as-builts.
- Resolve basic and detail technical and engineering mechanical and control design problems
- Prepared and administrated Safety and Clearance Tagging Procedure
- Prepared a complete listing of all air system isolation valves and the components affected by their shutoff
- Prepared Gas Blow Procedure and maintained total site control and supervision during gas blows

11/00-3/01 COMBINED CYCLE STARTUP MANAGER
OCM GANTT
James A. Vann, Jr. Power Plant, Two-on-One 500 Mw Combined Cycle Unit
Gantt, Alabama
- Prepared Start-up Package List, package content requirements and supervised development and completion of the packages
- Implemented OWDL (Outstanding Work & Deficiencies List) Tracking Program
- Established Cross Reference database for all EPC requirements to appropriate turnover documentation
- Issued Warranty Claims to Vendors
- Established Door, Panel and Equipment Key control and turnover, including index generation
- Established/Participated in Critical Path Method scheduling for Pre-operational Testing and Initial Startup and Operation phases
- Established Borrowing of Spare Parts and replenishment
- Established Vendor Rep Scheduling, Owner notification, Service Reports, Filing
- Determine/Implement Startup's role in Development, Review and Approval of Acceptance Test Procedures, Operations Manuals including Systems Descriptions and Integrated Facility Operating Instructions

8/99-11/00 COAL PLANT LEAD MECHANICAL COMMISSIONING ENGINEER
Black & Veatch International
Paiton Power Station Phase II, Coal Fired 2 x 610Mw (Siemens, ABB, BVI consortium)
Paiton, Indonesia
- Perform erection completion inspections, pre-startup equipment checks, integrated startup, testing and optimization of this prototype standard
- Resolve basic and detail technical and engineering mechanical and control design problems
- Technical interface between Client and Consortium Partners
- Technical issue tracking and expediting
- Turnover Package documentation completion
- Senior Authorized Person to establish isolation measures for designated systems
- Prepare and maintain Mechanical portion of all System Turnover Package and as-builts.
- Implement routine preventative maintenance program.
- Supervise/assign work to Mechanical Technicians and construction crafts.

1/99-8/99 ICS-24 HRSG COMMISSIONING MANAGER
ABB HRSG Group
Berkshire Power Station
Agawam, MA
- Develop Commissioning Inspection and Testing Plan
- Develop all Cold and Hot Commissioning procedures for equipment, integrated checkout and the performance test
- Perform erection completion inspections, pre-startup equipment checks, integrated startup and testing, and final performance evaluations of the HRSG and its accessories
- Provide Quality Assurance of Owners Turnover Package records during commissioning
- Assist Erection Advisor in resolution of construction, erection and engineering problems for this prototype Next Generation HRSG
- Assist in Product Line Development

5/96 – 12/98 INSTRUMENTATION & CONTROL LEAD TECHNICAL CONSULTANT
ABB-CEII, ABB Combustion Engineering International, Inc.
Ulchin Nuclear Generating Station 3&4
Ulchin, Korea
- Technical Advisor to the Startup and Permanent Plant I&C Departments during construction, construction acceptance testing, pre-operational testing, cold hydro, hot functional testing, and power ascension testing.
- Assist in NSSS system initial startup, checkout, and calibration including Modicon PLC's, Foxboro Micro Spec 200 control and process instrumentation, ABB-CE Protection and Control systems
- Assist in BOP system initial startup, checkout, and calibration including all Radwaste systems, Eaton Plms 32 Plant Control system, Eagle & Allen-Bradley PLC's, Primary and Secondary Sampling system, Turbine-generator auxiliaries
- Provide training and assistance in Protective System Pressure Ramp Response time testing, RTD response time testing, and Reactor Protection System Channel response time testing
- Provide extensive interface with overseas vendors for problem resolution of I&C, Electrical, and Mechanical systems
- Engineer corrections and field implement design deficiencies
- Provide configuration control and startup troubleshooting of Radiation Monitoring System computers, software and OS/2 operating system
- Assist in troubleshooting Plant Monitoring System (Plant Computer)
- Setup, train and troubleshoot Concurrent Temporary Data Acquisition System

12/93 - 5/96 OPERATIONS LEAD TECHNICAL CONSULTANT
Combustion Engineering International, Inc.
Yonggwang Nuclear Generating Station 3&4
Yonggwang, Korea
- Technical Advisor to Operations, I&C, Electrical, and Mechanical Departments during construction, construction acceptance testing, pre-operational testing, cold hydro, hot functional testing, power ascension testing, and commercial operation.
- Performed system walkdown and inspections during all phases
- Performed Test Working Group technical review of I&C, Electrical, and Mechanical System preoperational tests and test results
- Prepared Operations Hot Functional and Power Ascension Test Procedures
- Developed the NSSS and Turbine-Generator Warranty Test Procedures
- Performed Plant Nuclear Safety Committee technical review of power ascension test procedures and results
- Prepared Operation's test procedure test summaries and test reports
- Worked extensively with I&C Department to resolve problems on NSSS and BOP I&C systems
- Worked extensively with GE Technical Advisor to resolve all Turbine-Generator Operational issues and startup problems
- Interfaced with overseas vendors for problem resolution of I&C, Electrical, and Mechanical systems
- Prepared scheduling for testing phases and work outages for the units
- Assisted in performance, calculations and data analysis of the NSSS and Turbine-Generator Warranty tests

11/89 - 12/92 LICENSED SENIOR REACTOR OPERATOR TRAINING CONSULTANT
Arizona Public Service Company
Palo Verde Nuclear Generating Station
Wintersburg, Arizona
- Qualified classroom and training instructor for Initial License and Requalification Programs in all areas (I&C, Electrical and Mechanical)
- Developed and prepared classroom and simulator training program materials for Reactor Operator, Requalification, and Shift Technical Advisor
- Performed Senior Reactor Operator, Reactor Operator Task Analysis
- Delivered Initial License, Requalification, Shift Technical Advisor classroom and simulator training programs
- Developed Initial License and Requalification Program Exambanks
- Administered annual Requalification examinations and provided Requalification upgrade training

11/86 - 11/89 SENIOR REACTOR OPERATOR SIMULATOR PROGRAM DEVELOPER
Florida Power and Light Company
St. Lucie Nuclear Generating Company
Port St. Lucie, Florida
- Performed Senior Reactor Operator/Reactor Operator Task Analysis
- Developed Simulator training program for Reactor Operator, Senior Reactor Operator, Requalification and Shift Technical Advisors
- Developed Simulator Evaluation program and Job Performance Measures in accordance with NUREG 1021
- Upgraded all classroom and simulator training materials to incorporate procedure changes, plant modifications and industry lessons learned
- Delivered Shift Technical Advisor Training
- Developed software code for an automated exambank

3/83 - 11/86 LICENSE TRAINING INSTRUCTOR
Arizona Public Service Company
Palo Verde Nuclear Generating Station
Wintersburg, Arizona
- Developed and prepared Initial License training program materials in accordance with INPO accreditation criteria
- Delivered Initial License classroom training including NSSS & BOP Instrumentation and Control Systems, Mitigating Core Damage, and Transient Accident Analysis
- Developed and delivered training course in GE Mark III Analog Turbine Generator Control and Support Systems
- Administered annual site Requalification License Examinations

1/83 - 3/83 SIMULATOR ACCEPTANCE TESTER
Combustion Engineering
Windsor, Connecticut
- Performed acceptance test procedures and validation checkout of Calvert Cliffs simulator under construction
- Analyzed simulator performance for correct operational/theoretical response, direct interface with programmers/engineers and Fortran 77 code to determine the hardware/software deficiencies

2/81 - 11/82 SENIOR REACTOR OPERATOR
Illinois Power Company
Clinton Nuclear Power Station
Clinton, Illinois
- Performed/supported initial startup and testing of I&C, Electrical and Mechanical systems during construction, startup and turnover phases of this BWR 6
- Directed on-shift activities of reactor operators, plant equipment operators and test engineers
- Developed plant operational, surveillance and test procedures for I&C systems
- Performed technical review and audit of I&C startup procedures

2/80 - 2/81 COMPUTER/FIELD SERVICES ENGINEER
Bandag, Inc.
Muscatine, Iowa
- Installed and setup industrial testing computers at dealers nationwide
- Provided initial and continuing training on computer operation
- Performed computer troubleshooting and repair
- Performed I&C maintenance and calibration
- Performed electrical and mechanical repair of AC and DC drive equipment

10/78 - 2/80 ELECTRONIC ANALYST
Motorola, Inc.
Mt. Pleasant, Iowa
- Performed setup, calibration, troubleshooting and repair of manufactured electronics equipment
- Performed Root Cause Analysis on electronic component failure
- Provided initial and continuing training to forty electronic technicians

11/72 - 10/78 ENGINEERING WATCH SUPERVISOR / REACTOR OPERATOR
U.S. Navy
- Supervised I&C, Electrical and Mechanical Equipment Operators during overhaul, testing, and operational phases of a submarine PWR plant at sea and in overhaul
- Lead engineer in charge of I&C equipment operation, calibration, maintenance and repair
- Directed training and requalification of Reactor Operations Department

Accreditations
- PVNGS Senior Reactor Operator Certification
- NRC PWR Senior Reactor Operator, Docket No. 55-60176
- Clinton Power Station BWR 6 Senior Reactor Operator
- Navy- Reactor Operator, Nuclear Engineering, Radio Electronics Technician, Radar Electronics Technician, Advanced Electronics, Industrial Management and Supervision, Supervisory Skills for Industrial Managers

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 901 to 950 of 4409)

Go to Search Parameters...

Brief Description

35 continuous years of national and international commercial construction experience

The resume summary is included in the resume.

I am very experienced and have worked at all levels worldwide and also worked with many nationalities. I work very hard and get on well with everybody.

Mechanical & Electrical Engineer Location East London, Essex, Kent, Greater London Salary To £30,000 plus package

Safety Manager seeking position

Crane Operator

Civil Engineer with solid background in structural design, experience working with oil companies. Project supervision experience, costing and evaluation. Vast field experience leading working crews and supervising jobs. Good communications skills. Multilingual, speaking Spanish, French and Italian.

Experienced in power plant operations and startup.

international c.v.

Mining Engineer and Geologist with twenty-seven years’ experience in precious and base metals, coal and industrial minerals. Professional Engineering licenses in three states, with unique construction and engineering achievements. Advanced technical and strong supervisory skills.

Work Experiences : Mechanical equipment and piping installation in the following industrial plants: 1) Natural gas plant 2)Power plant 3)Polypropylene plant 4) Oil Refinery 5)Desalination plant 6)Steel mill 7)Foundry plant(maintenance of mechanical equipment)

I have been working in construction industry for Oil & Petrochemical Plant for decades. I work well under pressure and very keen on project planning and management. I am confident in leading a team of sub-contractors in performing sophisticatedly for any petrochemical processing plant.

NACE Certified Coating Inspector #7278, with +20 years of experience, available as (3rd party) Q.A./Q.C. coating inspector, coating surveyor, coating supervisor, vendor surveillance, etc.

I have been working in the Construction Industry for 40 years at all levels up to Construction Manager. I have extensive experience overseas including Africa and Asia. I am looking for similar work and am prepared to work anywhere at immediate notice.

23 years experience in the Electrical Distribution/Electrical Contractor Industry. Wish to acquire a part time or full time position in an office or job site environment.

Job objective: General Supervisor, Field Supervisor, Project Manager or Assistant Project Manager. Interested in overseas opportunities.

Looking for a new challenge at the end of 2003 my present contract end then

S.M.A.W.welder/demonstretor/application engineer in a welding electrods company xperience 8 year as welder/fabricator and 2 year as application engineer and demonstretor greduate and computer littrate

Heavy Equipment Operator Grader, Excavator all sizes, front-end loader and dozer, Class A CDL with all the endorsements

3-D mapping, preparation of Face logs, monitoring & analysis the defomation

Supply Chain Management, Cost Reduction, Global Product Management, Inventory Planning, Process Development, Cost Management, Vendor Management and Relationships

Repair and maintenance of class 1-8 trucks, trailers. Repair all systems of vehicles, including power, train, air, hydraulics, electrical, brakes, and transmissions

Good written and oral skills, a pleasing personality, a flair for dealing with people and ability to work in a multi-cultural group

Flexible and adaptable to any situations and environment

Document controlling.

Occupational health and safety trainer. More than 20 years experience with hazardous materials. Twenty one years military experience.

Has more than Seventeen (17) Years of continuous experience in Cost Engineering and Quantity Surveying works which involved the following:

Instrument engineer with around 15 yrs of versatile experience in the field of installation,commissioning , operation amd maintenance.

Drafting (Manually & computerized using AutoCAD 2D & 3D), Structural Analysis & Design of Building (Manually and computerized using STAAD & Microfeap Software’s), Construction Estimates, Plumbing/Piping Design, Surveying, Project Supervision and Computer Literate (Microsoft Word,Excel & Powerpoint)

Over 25 years of diverse and successful experience in material control in areas including: Nuclear/Coal Power Generation, Bulk Handling & Storage, Co-generation, Commercial Maintenance, Oil Refinery, Warehouse/Distribution, Shutdown/Turnaround and Outages.

Experience in all phases of material management & expediting, design office & engineering & project coordination. Experience in heavy construction including offshore oil platforms & related facilities, nuclear fuelled power plants, paper mill, chemical plant & overseas military facilities.

I am a Graduate Mechanical Engineer and have good proficiency in Computers. I have put in 13 years of hard work in Construction of Oil & Gas Pipelines, which has given me exposure in all fields like Project Management, Planning, Tendering, Cost Estimation and Control, Execution.

Geodesist/Land Surveyor/Geomatics/GIS consultant

Project Manager with over 35 years of experience in the construction industry, which offers an extensive and diversified array of industries such as power generation, pharmaceutical, semiconductor, large office facilities, pulp/paper and plastic projects, coal gasification and others.

Highly motivated and results-oriented professional with exceptional leadership and interpersonal skills with an extensive background in construction industry.

A competent Chartered Mechanical Engineer with over 14 years experience, gained in Aluminium, Iron & Steel, Nuclear & Petrochemical Industries. Worked in areas of Design, Construction, Installation, Projects, Commissioning, Overhead Cranes and SAP.

Piping/Mechanical Superintendent

System Admin for IT Industry.

RESIDENT CONSTRUCTION MANAGER / SUBCONTRACTS MANAGER / CONSULTANT IN CONSTRUCTION OF PETROCHEMICAL PLANTS (SPECIFICALLY HYDROGEN /SYNGAS REFORMERS, ETHYLENE CRACKING FURNACES, PETROCHEMICAL UNITS INCLUDING DETAIL PLANNING AND EXECUTION OF SEVERAL PLANT TURNAROUNDS PROJECTS)

30 years experience in all types of heavy industry, the equipment used, predominately in coatings and linings. Experienced in all phases of construction projects. Supervised numerous larger projects, overseen and implemented safety, inspection.

I am currently on another project but can leave with a two week notice.

I have been supervising and managing Building projects for the past 20 years With great success. I am not only a man Who is a supervisor but I have journeyman Level skills at most of the major trades, This allows me to insure proper quality.

results oriented, hands on, Construction Management person with 20+ yrs experience in various facets of the industry specializing in Industrial, Mining Construction. Prefers international or remote work location.

Have been in construction for 35 years

Experienced Maintenance Mechanic/Welder with twenty-five years in the maintenance field. Skilled in all types of mechanical work- hydraulic, pneumatic, conveying systems

Award winning Project Manager / Facilities Engineer.

Extensive experience in the construction of industrial buildings, Multi-story buildings, Steel Structures, Water Structures, Infrastructures Writing Progress Reports, Maintaining and Coordinating Construction work schedules Computer skills: Office 2000, Primavera 5.1, Auto CAD

Extensive background in the planning and profitable management of large scale projects/ programs in support of multi-million dollar business operations.

ELECT. ENGGR WITH 21YRS+ CONSTRUCTION SUPERVISION EXP.PG DIP IN CONST MANGMT AND MSPROJECT PI PPM. INVOLVED IN PROJ MANAGMT CONSULTACY FOR ELECTRICL/PLNNG COORD/QUALITY ASSURANCE COORD AND HSE MANAGEMENT.

Power Generation- Twenty-eight years experience of Construction, Startup & Commissioning, Operations & Training for Combined Cycle Units, Coal Fired and Nuclear Steam Supply Systems (NSSS) & Balance of Plant (BOP) Systems as Lead Mechanical, Lead I&C, Lead Operations and Startup Plant Manager.

First 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 [ 19 ] 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Next Last

Seach Parameters


Change search parameters...
INDUSTRIES: Construction;
Change search parameters...
Keywords: (e.g. mining engineer)		Find results with:


Save this search parameters...
Post job with this search parameters...

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out