CONTACT INFORMATION:
View contact information...
SKILLS: Mechanically Inclined, Detail Orientated, Organized, And Reliable Person.
Over 25 years expiereance. Over 20 Years Catia, Over 5 Years Wire Harness Design.
WORK EXPERIENCE:
SPIRIT AEROSYSTEMS INC.(CONTRACT)
January 2007 Senior Catia Designer: Boeing 747-8 Program,Nose Wheel Well Group
To Present Job Duties: Design and Detail of Stiffener Beams and Shear Tie Strap for Aft Side Panel - Nose Wheel Well. Design and Detail of Stiffener
Beams, Shear Clips and Station 260,280,300 & 320 Choord Assy for
Fwd Side Panel - Nose Wheel Well. (All Parts Created Using Solid-E Model)
Created Installation Assembly Drawing for Fwd Side Panel - Nose Wheel Well.
Catia V4, Solids, Fly-Thru, Windows.
DASSAULT FALCON JET CORP. (CONTRACT)
September 2005 Senior Catia Designer: F7X Interior Wiring Group.
To December 2006 Job Duties: Design and Packaging of Wiring Harnesses for
Aircraft 004,005,006,007
Design of Rad/Nav-Main Cabin (005,006,007)
Audio/Video-Main Cabin (007)
A/C Power- Main Cabin (006,007)
Rad/Nav-Baggage Compartment (004,006)
PSU-Headliner Fwd,Mid,Aft (006)
Main Cabin-Headliner (005)
Aft/Lav-Headliner (005)
Design of Cabinet Wiring for Fwd/Lav,Aft/Lav,Main Galley,
Galley Annex, Crew Rest (006)
Frame 30 Bulkhead and Mid Cabin Bulkheads (006)
Sideledges (005,006,007)
Using E3D, Catia V4, VPM, Estel Database, Some V5.
Q.E.D.
April 2003 Senior Catia Designer: Interior Trim Group 2007 JS, PT, PM, RS.
to September 2005 Job Duties: Design of Door Trim Panel, I/P Center Stack, I/P End Cap
A/Plr Trim For Libralter Plastics. Design of Inner Wheel House,
Stone Shield For Sarnam Automotive. Utilizing VPM for model data retrieval and releasing. Catia V4, CDV.
EDAG INC.
November 2002 Senior Catia Designer: Electrical Group - M80 Feasibility Study.
to April 2003 Job Duties: Design of brackets and packaging of electrical underhood components, PDC module, ECU module, FCM module, trans module, brake module, speed control module, air bag sensors, brake sensors, ambient temp sensor, horns, headlamps, hood light, hood light switch, battery. Packaging of tail lamps, third brake light, speakers, subwoofer, tweeters, amplifier, radio, cluster, headlamp switch, hvac control unit. Design of wiring harness and wire routing using E-3D for headlamp & dash, chassis and battery harnesses. Utilizing VPM & CDM for model data retrieval and releasing. Catia V4, CDV.
MSX
November 2000 to Senior Catia Designer: E/E Systems - 2001-2003/PT Program.
October 2001 Job Duties: Design of wiring harness and wire routing using
E-3D for headlamp & dash, crossbody, instrument panel, headliner, body and door harnesses. Utilizing CDM for model data retrieval and releasing. Catia V4, CDV.
Work Experience (cont'd)
MODERN ENGINEERING INC.
November 1999 to Senior Catia Designer: E/E Sytems - 2002/CS Program.
November 2000 Job Duties: Design of brackets and packaging of electrical components. Design of wiring harness and wire routing using
E-3D for liftgate, power liftgate, door and headliner harnesses.
Utilizing VPM & CDM for model data retrieval and releasing.
Catia V4, CDV.
TG NORTH AMERICA CORP.
July 1998 to Senior Catia Designer: Body Weather Seals - JR/27 Program.
November 1999 Job Duties: Created surfaced and faced models for front door primary seal & molded detail, front door sill seals, deck lid seal, sash seal, convertible top rail seals, header and A-pillar seal assembly, A-pillar molded detail, inner belt seal and mirror flag seal assembly. Utilizing CDM for model data retrieval and releasing. Catia V4.
COOPER TIRE & RUBBER CO.
May 1997 to Senior Catia Designer: Body Weather Seals - JR & JA Programs.
July 1998 Job Duties:JR Program - Created surface and faced models for front and rear door primary seals, front and rear door sill seals, decks lid seal, hood to cowl seal, hood to radiator seal, drip rail seal and molded detail, wheel house seal, window corner mold.
JA Program - Created surface and faced models for front and rear door primary seals, front and rear door sill seals, decks lid seal, hood to cowl seal, hood to radiator seal, drip rail seal, molded a-pillar molded detail.
Utilizing CDM for model data retrieval and releasing. Catia V4.
DGE SERVICES
September 1991 to Senior Catia Designer: Body Electrical Group / Chrysler Jeep and Truck Engineering.
April 1997 Job Duties: Design of brackets and packaging of electrical components,
J-tech module, S-beck module, trans module, PDC module, speed control module, air bag module, air bag sensors, horns, speakers, radio, amplifier, window switch, door lock switch, headlamp switch, door ajar switch and brake light switch. Design of wiring harness and wire routing for crossbody, instrument panel, engine and transmission harnesses on 1997/TJ Jeep
Wrangler Program. Utilizing CDM for model data retrieval and releasing. Catia V4.
MODERN ENGINEERING
May 1990 to Senior Catia Designer: General Motors A-Body Program / Interior Trim Group.
September 1990 Job Duties: Design of door trim panel, door handle bezel. Catia V4.
PREMIER ENGINEERING
February 1986 to Senior Catia Designer: Chrysler - Body Electrical Group.
May 1990 Job Duties: Design of brackets and packaging of electrical components, body controller module, air bag module, air bag sensors, speakers, radio, amplifier, cluster, window switch, door lock switch, headlamp switch and dome lamp. Catia V4.
REFERENCES FURNISHED APON REQUEST
View contact information... |