Resume - ISO/ASNT certified Vibration analyst ,More than three years of engineering exper...

Misco Jobs

Resume #87105

CONTACT INFORMATION:
View contact information...

A talented Mechanical Engineer with experience in Condition based maintenance and Vibration analysis. looking to improve my skills and my experience in an international organization

Summary
******
-ISO/ASNT certified Vibration analyst
-More than three years of engineering experience.
-Analytical skills and self learning ability.
-committed to any work unconditionally.
-Able to work under pressure.
-Able to liaison between technical groups.
-Proven ability to improve efficiency.
-Hard working and detail oriented.

PROFESSIONAL EXPERIENCE
***********************

Arab Swiss Engineering Co. ASEC, Cairo, Egypt June 2007 – Present
Condition Based Maintenance (CBM) Engineer.
"Vibration Analyst" ISO/ASNT Certified

-Collect data and analyze vibration signature using all analysis techniques such as Cross Phase analysis, ODS, Run up and Cost down tests, Bump test, Peakvue …etc. to detect and diagnose any problem before it leads to failure in several cement manufacturing plant such Helwan, NCC, Sinai and Masr Bani Swif plants.
-Using CSI analyzers 2120 and 2130 Pro Consultant and its software "AMS".
-Correct mechanical unbalance problem by applying in-filed balance jobs "multi plan and multi speed" using different balance techniques such as "static-couple balance" and flash angle "one shot balancing".
-Writing monthly technical reports about the machinery health with clear explanations and professional recommendations and supervise applying these recommendations.
-Built up a data base for the equipments and select the equipments which go into the route.
-Built up proper case studies.
-Measuring and diagnosing faults of Bearings, Gearboxes, Electric Motors, Air Blowers, Fans, Air Compressors, centrifugal pumps, piston pumps.

Egyptian Engineering Co., EEC, Cairo, Egypt November 2006 – May 2007
Site/Office Mechanical Engineer

-Mange the operation of building water treatment stations, job involved designing and mechanical drawing skills.
-Designed water treatment units and stations and select the layout of these stations

--------------------------Total years of Experience: 3 years-----------------------------

EDUCATION
*********

Helwan University, Cairo, Egypt
B.S.C in power Mechanical Engineering, 2001- 2006 Grade Good
Graduation project Studying the performance of centrifugal compressor at variable speed.
Grade Excellent

Mobius Institute, Victoria, Australia
Vibration Analyst ISO/ASNT certificate Category II May 2009
Certificate Number 080704

TECHNICAL SKILLS
****************

MS Windows (98, 2000, xp and vista), AutoCAD, Swish, MS Office, Machinery Health Manger "AMS"

LANGUAGES
*********

Arabic Mother tongue
English Very Good "writing, speaking and understanding"

ADVANCED TRAINING
*****************

-Mobius Institute – Natcom –Advanced vibration training III - 2009
-Mobius Institute – Natcom –Intermediate vibration training II - 2009
-SKF - Vibration Analysis and condition monitoring level 2 - 2007
-TCC Technology Competency Center - Operating and maintenance of pumps - 2006
-TCC Technology Competency Center - Hydraulic & Electro hydraulic system - 2006
-Suez Oil Processing Company- Summer training - 2005
-Egypt Air Company – Summer training - 2004

PERSONAL INFORMATION
********************

Date of birth October 21st 1984.
Nationality Egyptian.
Marital Status Single.
Military Service Exempted.

Keywords: Mechanical Engineer, Condition based maintenance engineer, Vibration analyst, Design Engineer
Certificate online reference: http://www.mobiusinstitute.com/mi/CategoryIIStudents.html
Last update: 22nd July 2009

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 801 to 850 of 1619)

Go to Search Parameters...

Brief Description

Construction Management/Estimating/Supt/PM

Electrical engineer, Constraction, Control & Instrument, Coal, Oil & Gas projects,

Chief Enineer, Limited, Oceans, Unlimited HP

Jamiu Badmos is a Registered Engineer cum HSE Professional with over 9yrs experience in QHSE & Project Management

Western IT and data networking expertise. Enterprise and Telecom experience. PMP holder

Handle preventive maintenance for the machine , servicing machine ,replace breakdown component /or equipment.

RSLogix 5000, PLC 5, SLC (Allen Bradley) Concept (Modicon, Quantum) Unity (Modicon, Quantum, M340, etc.) Setting up and commissioning of Advantys IO systems Rockwell, RSView Wonderware, Intouch

MSc Engineering / Business Development / Project Management /Energy fielsd

Environmental pre-construction surveys for wetlands, streams, and wildlife habitat; knowledge of wetland plants, soils, and delineation rules as well as general ecological knowledge. 10 years of experience on pipeline projects.

Fully qualified safety proffesional, with extensive experience in the construction industry, Rigging & Lifting Supervisor and Qualified Engineer please review CV for all qualifications & working background

ISO Implementation, Documents, Records, Archival Management, QA Manager, Writing Technical Documents, Auditor

Certified Safety Professional with over 20 years experience, in multiple industries, including oil and gas, medical, transportation, environmental and manufacturing.

Quality Control professional

Rotating & reciprocating equipment technician

Research Experience: Polymer solutions and adsorption behavior.

Looking for Instrumentation and controls job

Professional Land Surveyor

Electrical Engineer and Computer Sciencer

I graduated Lakeland College’s Environmental Protection Technology Program in April 2009. This summer and last I worked as an Environmental Research Technician with the Native Plant Development and Habitat Restoration Program at the Alberta Research Council in Vegreville, Alberta.

1. Designing, Estimating and Costing 2. To make the perspective techno commercial offer

I am a qualified Metallurgy and Materials Engineer with international research and training experience. I am a person with strong organizational skills and am very confident in analyzing and solving problems with positive outcomes. My past studies in Metallurgy and Materials Technology and the resea

Proficient in reading mechanical drawings and designing using Auto Cad, CATIA, NX-IDEAS.Strong Technical writing and presentation skills along with good hold in MS - Office.Master of Engineering (G.P.A - 10.33 out of 13)(2008- 2009)University of Windsor.

Summary of Qualifications: Proficient in this engineering software: 3D - PDS Equipment, Piping modeling/design,Isogen, SmartPlant Review, Microstation, AutoCad. Industries: Nuclear, Energy, Power, Petroleum / Refinery, Chemical, Logistics, Transportation, Manufacturing and Defense.

Word packaging

Mechanical Engineer, technical support

Eco-friendly Architect, Revit, Autocad, 3D max, SketchUp, Photoshop, Flash, Coral-draw, Illustrator, Rhino3D.

Basic Soft Skills (Communication Skills, Presentation Skills, Team Working, Technical & Business Writing)

3rd Year Enviromental Technologist

Sales, Engineering Project Manager

Mining and geological engineer from the university of Liege with a specialization in geophysical methods and geotechnics.

Project Manager, Field Engineer, Commissioning Electrical Switchgear

ISO/ASNT certified Vibration analyst ,More than three years of engineering experience ,Analytical skills and self learning ability,committed to any work unconditionally,Able to work under pressure,Able to liaison between technical groups ,Proven ability to improve efficiency

I have 3 years experience in the Design industry. I self taught myself on AutoCad and Microstation.

Experience in Instruments of PERKIN ELMER and applied bio-system, installation, commissioning, maintenance, and calibration of various instruments;

Electrical Engineer with wireless, optical and integration expertise

Applying for the post of safety officer in your esteemed concern

Mechanical/Manufacturing Engineering, Project/Program Management, Supply Chain Management

Environment, safety, health, quality, security, international, lean manfuracturing, construction, operation, management

PhD (Geology), Post MSc Diploma (Hydrogeology), MSc (Applied Geology). Working as GIS Professional and previously worked as Geologist, Lecturer in Environmental Science and GIS Professional.

Computer Technician

Principal Environmental & Safety Consultant, oil, gas, mining & major projects; EIA, EMS, Environmental risk etc, climate change, HAZOP, HAZID, Safety managment etc experience. Relocating to Vancouver. Has right to live and work in Canada

Automobile related

Electrical Engineering, Energy Systems, Power electronics

I am Diploma in Mechanical Engineering. I have adequate knowledge in Auto-Cad in mechanical engineering field. I also have confident experience in X-Steel & SDS2 in steel structure back ground.

Graduate Electrical with Power Electronics

Environmental Engineer and Senior Project Manager

Prevent / correct unsafe acts & condition.

Project Manager - Sales - Technical

I am 26 years old engineer of hydraulic and searching for traineeship in companies in Germany, Austria, Italy to get more and better experiences in my field of work and to grow in knowledge.

Over twenty years of experience

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 [ 17 ] 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

Seach Parameters


Change search parameters...
CATEGORIES: Engineering/Technicians; INDUSTRIES: Environmental;
Change search parameters...
Keywords: (e.g. mining engineer)		Find results with:


Save this search parameters...
Post job with this search parameters...

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out