Resume - Overhauling of Rotating equipments e.g pumps, compressors, gas turbines etc. in ...

Misco Jobs

Resume #26708

CONTACT INFORMATION:
View contact information...

To,
The Recruiting Manager,

SUBJECT: Application for the post of Mechanical Supervisor/ Sr. Technician

Dear Sir,

Being given to understand that your esteemed organization is recruiting qualified and experienced staff in the field of Mechanical Maintenance, I wish to forward my C.V. for your kind perusal.
Presently working in Occidental Petroleum Qatar Limited as a Sr. Mechanical Technician
Since November 2004.
Worked with Shell Petroleum Development Company, Nigeria as a Mechanical Supervisor for two years.
Prior to this I was working in the Gas Plant of Conoco Syria Dez Gas Ltd., CSDGL, Syria as a Supervisor responsible for Nuovo PignoneTurbines and Centrifugal Compressor Maintenance for six months.
I have also worked on an FPSO ( Floating Production Storage and Offloading) based at Equatorial Guinea offshore as a Maintenance Supervisor for a period of one year.
Before these short stints in CSDGL and On the FPSO which were due to better prospects I worked in Al- Furrat Petroleum Company Syria as A senior Mechanical technician from October 1995 and later on promoted to a Supervisor from March 1999 till October 2000.
I have a total experience of 16 years after completion of a three-year trade
Diploma from Bharat Petroleum Corporation Ltd., India. I also served in the same
Organization from 1986 to 1995 as a Mechanical Technician.
If my qualification and experience suits your requirement I am willing to be interviewed at your convenience.
Thank you for time and consideration and expecting a favorable reply.

QUALIFICATIONS
ACADEMIC:
Passed Inter Science through Pune divisional board with Maths, Physics and Chemistry as major Subjects.

PROFESSIONAL:
Completion of a three-year trade Diploma in
Mechanical Maintenance from Bharat Petroleum
Corp. Ltd. (1983-1986)

EXPERIENCE:
Worked in Bharat Petroleum Corp.Ltd
(Refinery) since September 1986 to Oct. 1995.
ABROAD: Presently working in Occidental Petroleum
Qatar offshore as a Sr. Mechanical Technician
Since November 2004.

Worked as an oilfield Maintenance
Supervisor in Shell Petroleum development
Company (SPDC) Nigeria since October 2002.

- Worked as a Supervisor for Maintenance of
Turbines and Centrifugal Gas Compressors from
June 2001 to October 2001 in Conoco Syria Dez
Gas Ltd., Syria.
- Worked as Maintenance Supervisor on an FPSO
From Oct. 2000 -June 2001 offshore in
Equatorial Guinea.
- Worked as a Supervisor in Solar turbines Maint.
From March 1999 to August 2000 in Al- Furrat
Petroleum company Syria From October 1995 to
Feb.1999 as a Sr. Maintenance Technician in
Al- Furrat Petro. Company, Syria.

FACILITIES IN GAS PLANT
Gas pant consists of NGL Extraction, LPG fractionation, export gas compression, power generation, ethylene glycol injection, propane purification, hot oil system, fuel gas system and a pre-cooling unit.

DUTIES AS A SR. TECHNICIAN
1) To carry out preventive maintenance as per the Impower system of
Scheduled maintenance.
2) To carry out trouble shooting, break down maintenance and pre-
Ventive maintenance of Rotating and Static equipment's in the gas
Plant such as:

EQUIPMENT MAKE SERVICE

Centrifugal Compressor – Dresser Rand – For Gas compression
Nuovo Pignone

Gas Turbines - Solar
Centaur type H – Power Generation,
- Nuovo Pignone - Gas Compression,
- Alstom, Tornado - Water Injection pump

Air Compressor - Broom wade, - Instrument /Utility air
Ingersoll Rand,
Air Dyne.
Pumps - Union, Gould, - Process requirement
Kerr, Sulzer.

Fin Fans - Hudson - Cooling

Gear Box - Allen, Solar - Reduction between
Solar Turbines and Driven.
Heat Exchanger - Hudson - Gas Cooling

Any other Mechanical Jobs concerned in the Refinery and Gas plant.

DUTIES AS A SUPERVISOR

1) Determine material requirements and order using procurement system such as EMA (electronic material administration), includes raising of MIV (material issue voucher) and MR (material Requisition)

2) Demonstrate problem solving skills both technical and non technical

3) Promote high level of safety awareness, by completion of unsafe act reports / near miss reports/tool box talk.

4) Ability to manage resources, Manpower, materials and equipment

5) Has the necessary skills to analyse plant equipment and process
Problems and develop solution.

6) Maintain daily records, execute the 14-day plan, prepare permit in
Accordance with the permit to work plan, complete all outstanding work orders.

7) Possess an acceptable level of PC literacy.

8) Demonstrate the ability to compile and communicate end of shift workCycle and hand over to a satisfactory standard.

JOB DESCRIPTION:

As a Sr. technician/ Supervisor developed the following skills.

Worked with confidence and independently on all rotating equipment, which includes complete strip down and preventive maintenance of the same.

1. PUMPS:
Makes: Hayward Tyler, Gould, Nuovo pignone, Kerr, Sundyne,
Stork Pacific, Sulzer Bingham etc.

Trouble shooting and fault findings on pump failure.
Overhauled all types of pumps such as Centrifugal, Reciprocating and Rotary pumps.

a) Obtaining a complete check list of the dismantled equipment and
Keep a record of the same.

b) Inspect the condition of rotating parts namely shaft, sleeve, impeller,
Oil deflectors, coupling and stationary parts such as casing, stuffing box, distance piece, and bearing housing.

c) Renewal of Mechanical Seals, checking wear ring and throat bush
Clearances.

d) Maintaining the required float in multistage pumps, check end play.
e) Checking the endplay, squareness and concentricity using a dial guage while pump assembly.
f) Hydro test of pumps to determine mechanical seal and casing leaks.

2. MECHANICAL SEALS:

Makes: John Crane, BorgWarner, Flexibox.

Refurbished all types of single, double, tandem and cartridge seals, Having single, multi-spring and bellows.
Renewed packings, seal faces and maintained operating length lapping seal faces to the required finish.

3. GAS TURBINES

Make: Solar Centaur type H split shaft and single shaft, Solar Saturn
Generator sets.
Alstom Tornado Duel fuel twin shaft
Nuovo Pignone twin shaft.
PLC: Enhanced 5/20, 5/15

Involved in minor, intermediate and major servicing and inspections.
Familiar with fault diagonistics, repairs and overhauls of auxiliary equipment, trouble calls and instant response.
Knowledge of basic turbotronic 2.0 using Allen Bradley PLC

Carried out Combustion Inspection, hot gas path inspection and also involved in complete strip down and change outs of HP and LP rotors
Of Nuovo Pignone Gas Turbines.

1) Periodic servicing of gas Turbines which includes replacing filters of lube oil, fuel electohydraulic start system and enclosure/ intake duct.
2) Inspection of Igniter plug, torch assembly, fuel injector and bleed valve
3) Simulation of Inlet Guide Vanes to check for max / min open.
4) Borescopic inspection to determine condition of stator, rotor blades
And Combustion chambers.
5) Water wash of Turbine, note the following prior to and after Water wash, a) Turbine Rotor speed b) Ambient temperature c) Engine T5 temp d) Compressor discharge Pressure (Pcd)
e) Simulate Ngp speed, T5 temperature and check operation of back
Up overspeeds switch using Solar test Kit.

TROUBLE SHOOTING:
Trouble shoot problems in the package with the aid of Allen Bradley programme such as:
Fail to ignite, Fail to start, Fail to crank, T5 temperature hi, Lube oil
Pressure low, Ngp overspeed, Npt break away, fail to accelerate, does
Not change over to liquid, Hunting, Failure of magnetic speed pick up etc.

Carried out engine change out after 35,000 hrs running.
Alignment of Turbine and compressor in case of Mechanical drives,
And turbine and gear box in case of generators

4. CENTRIFUGAL COMPRESSORS
Make: Dresser rand 2508B, Nuovo Pignone.

Involved in complete strip down and re assembly of centrifugal compressor.
a) Removal and assembly of Rotor bundle.
b) Inspection of diaghpragms, diffuser, thrust and radial bearings.
c) Maintaining overlap and axial float between stages d) Renewal of 'O'rings.
e) Locate position of rotor assembly and proper installation of gas seals.
f) Removal and reinstall journal bearings, thrust bearings and thrust disc.
g) Fit back Rtd's, axial and radial probes h) Use of special tools for Bundle removal /installation.

5. AIR COMPRESSORS
Make: Broomwade, Ingersoll rand, William and James, Atlas Copco.

Preventive maintenance and complete overhauling of compressors used for instrument air, utility air and to produce Nitrogen a) Replacing piston rings, guide rings, rod packings and adjustment of
TDC and BDC.
b) Replacing main bearings and big end bearings.
c) Refurbishment of suction and discharge valves.
d) Renewal of cylinder liner.
e) Worked on the unloader device of compressor.
f) Refurbished screw compressors.
Trouble shooting such as long interval between load and unload, low lube oil pressure, psv releasing, belts breaking, cooling water pump fault, inter cooler and after cooler leakage.

6. DIESEL ENGINES
Make: Caterpillar, lister, perkins.

Preventive maintenance and strip down of diesel and gas engines.
a) Fault diagonistic after compression test to detect leaking piston rings,
Valves, head gaskets or excessive carbon deposits on combustion chamber.
b) Renewal of cylinder heads, piston, liners, connecting rods, bearing and seals.
c) Check axial float, crank deflection, cam shaft, flywheel and turbo
Charger.
d) Adjust valve lash and replace Fuel injectors.

Periodic maintenance of diesel engine which involves changing sump oil,
Air filters, breathers, oil filters and radiator coolant.

7. GEAR BOX AND FIN FANS
Worked on Gearboxes, checking condition of low speed and high-speed shaft gears.
Check backlash and axial float.

Worked on Fin Fan coolers in the refinery and Gas Plant.
Motors to fan pulley alignment, replacement of belts, alter blade angle and routine maintenance.

8. VALVES:
Make: Cipeg, Cameroon, Argus, Crosby, Valgrove and Powell.

Overhauled all kinds of valves including Gate valves, Globe Valves, Needle valves and pressure and safety valves.
Renewal of valve seats or lapping of seats, change packings, caliberate and set required pressure for pressure and safety valves.

9. STATIC EQUIPMENTS
Worked on Static equipments such as Heat Exchangers, Columns and Vessels. Assisted in removal and refit of Tube bundle.
COURSES ATTENDED:

a) Five days Solar Centaur Turbotronic 2.0 Field Maintenance and Trouble shooting.
b) Seminar on Seals by John Crane c) Rotalign laser alignment.
d) Permit to work e) Fire fighting f) Breathing Apparatus g) Gas testing
I) Helicopter Underwater Escape Training ( HUET)
j) Basic First aid Course k) Swimming Test, SPDC Water Borne Operations Permit.

I wish to be considered as a candidate for the post Of Mechanical Supervisor/ Sr. Technician.

I have furnished my details for your kind perusal.

If selected, I assure you to serve with hard work and to the best of my ability.

Awaiting for a favorable reply

Thanking You.

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 8651 to 8700 of 15496)

Go to Search Parameters...

Brief Description

8 years experience in downstream logistics. Developed logistical planning for crude oil transportation via Caspian Sea to Black Sea ports, good communication skills. Demurrage claim settlements, reduced third party demurrage claims by $3 million during 4 years.

Currently a Cryogenic gas plant operator 3 yrs. Well Head compression experience 1yr. Associates Degree in Electronic Instrumentation and Control.

b.sc with first class and 2.8 years of experience in chemical/petrochem industry

Graduated from Geological Engineering, Faculty of Earth and Energy Technology, Trisakti University Jakarta in August 2008 with cumulative grade point average (GPA): 3.14 (scale from 0 to 4). My organization experience as membership of Gathering Student Board of Geology in Trisakti University

Competency in developing HSE Management system and conducting compliance audits, advising on HSE requirements & statutory compliance.

Marine engineer seastaff 15 years/eng superintendent 5 years/ operations manager 4 years/ technical manager 4 years

Great expierience and offshore back ground

Drafter, Designer, AutoCAD, Revit, CADD Manager, VB, VBA, AutoLisp, Access database, MS Office

Sr. Field Engineer, 20+ years, excellent customer service skills, electro-mechanical repair, maintenance

I'm a diploma holder in Chemical technology having 12 yrs of experience in petrochemical field worked as Junior Engineer in Ammonia synthesis plant of all sections of desulphurization, catalytic reforming,CO2 removal, synthesis reactor, refrigeration, ammonia storage with adequate HSE practices

I am a mechanical technician I can do all rotary and stationary equipment jobs.

my expertise are using any release of autocad, rhinoceros for 3d and GHS for stability calculation.

Reliable, hard working Geologist with experience in Environmental Consulting and Geophysical Investigations .

Degree and diploma in chemical engineering.

Experienced in developing and delivering drilling plans, including wellbore and casing design,mud program,cementing program, directional plan, completion design, leading risk assessments, developing safety programs for workover, drilling and completion operations on exploration and development wells

Seeking a challenging career position where my technical skills, talents can be effectively utilized by a company offering long-term opportunities for professional growth in recognition of dedication, drive and superior performance.

I have been in Customer service Line since 10 years. I have experince towards handling customers and solving the inquiries as well. Further more my qualification are until SPM but the working experince towards this line giving me a lot of opportunity to built up my career.

Have worked 9 years in mining industry. during this period i worked as dumptruck operator, l.h.d operator, jumbo operator, shift coordinator and drill master. what i like and enjoy of my work is the challenge of keeping my-self,

I am a Journeyman licensed plumber with electrical certification(NC) I have OSHA competent person training for heavy equipment and excavation. I am gas tite certified and a good mechanical skil set.

I Started at Newmont Gold Company In 1996 as a miner trainee, within one year I was promoted to miner 3. I also worked for Stillwater mining corporation in Montana where I was a lead miner in charge of 15 miners and two levels of the mine.

Young energetic hard working safety conscious person with good experience in comissioning training and optimization of a gold treatment plant

Underground Mining, Roof Support team.

Holder of the diploma in safety and health and certified in indsutrial hygiene management, holder of the NEBOSH certifcate in OSH

Self-motivated with experience in field of instruments, process, oil&gas valve and actuator control system. Knowledge, understanding and interesting in variety of control systems such as DCS, PLC, SCADA, and MARK series.

Microstation, AutoCad, Electrical Utility as well as Residential/Commercial, Pipeline Drafting and GIS

Safety Trainer seeking entry level position with Safety minded company.

Mechanical engineer with 13 month experince in production

I studied B.E.,in Instrumentation and control Engineering with 75% and First class with Distinction

Registered Nurse with one year working experience in different special areas like ICU,EMERGENCY DEPARTMENT,RECOVERY ROOM,SURGICAL AND MEDICAL WARD

Seeking a position in Project Management to utilize my Practical & Theoretical knowledge as well as technical skills so as to serve the firm for long time, which enables my professional growth. To work efficiently and honestly for the betterment of the organization and personal development .

7 Years of experience in Installiation,Testing & Commissioning of Electrical Equipments in the field of Power Stations,Petrochemical Plant etc

I am a red seal electrician with 7 years exp. I have worked sinking shaft & development.

civil formwork

B.Tech., Diploma., Civil engineering

I have worked as a drilling supervisor for 5 years and at the moment for 1.5 year work as a completion and drilling material specialist for national iranian oil company. I am ready to relocate internationally regarding to job situation.

Mechanical Design Engineer for Oil and Gas with 10 yrs exp. for EPC companies

Paint Inspector/Supervisor

Electrical and instrument project manager construction, design and inspection

Open Hole LWD Logging and log analysis, M.Tech (Applied Geology)

My most recent experience was repair and maintenance on board a Tanker vessel, Livestock and Reefer Ship. I was responsible for all the hot work and repair, including the use of Manual lathe machine

Overhauling of Rotating equipments e.g pumps, compressors, gas turbines etc. in an oilfield

Presently working with ConocoPhillips Syria Dez.Gas Ltd. since April 2002 as a Senior Warehouse & Procurement Supervisor in Syria (Middle East) on 28 Days ON/OFF schedules through GMOS (MSI). Job Profile: Responsible overall for all aspects of materials including warehousing, procurement operations

Working In the Oil and Gas Drilling Industry Since 1986 Looking for a company that wants its employers to look after it !!

Rotating Equipment Mechanical Engineer

Civil Engineering,Construction Manag., Geotechnical, structure, Design of steel towers

Senior Geologist (16+ years oil and gas experience), graduated in geology from University of Kansas in 1987.

I am currently working in a Water Utility Company as a Project Development Manager with exposure in designing pipe network, supervision of pipelaying works, and pipe maintenance, handles customer service operation, and Customer and Billing computerization project.

Looking to join a company that has the need for civil engineer and offers opportunities for advancement.

Having 15 years of experience in oil and gas construction and maintenance feild, with Diploma in Industrial safety, Environmental management

Electrical instrumental and electronic tecnician with 16 years experiences with very good knowledge mechanical and hydraulical system, Spécialized in open pit mining operation

First Prev 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 [ 174 ] 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 Next Last

Seach Parameters


Goto Advanced Search...
Keywords: (e.g. mining engineer)		Find results with:

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out