Resume - Over twelve years experience in Offshore and Onshore Oil & Gas and Marine Struct...

Misco Jobs

Resume #3950

CONTACT INFORMATION:
View contact information...

STRUCTURAL ENGINEERING

DATE OF BIRTH: 06/11/1967
NATIONALITY: Iranian
FAMILY STATUS: Married
LANGUAGE: Persian – English

QUALIFICATIONS:
Bachelors of Science in Hydraulic Structure Engineering, Sharif Technical University, Tehran – Iran (1990)

ROFESSIONAL MEMBERSHIP:
Iranian Society of Civil Engineers
Canadian Society of Civil Engineers

TRANING:
SACS Program Education, ANSYS Program Education
SAP2000 / ETABS 2000 / SAFE 2000 Programs Education
Pile Driving Analyser (PDA – Software), Wave Equation Analyser (GRLWEAP – Software), Pile Integrity Tester (PIT-PC Software), Certificate and Training

KEY EXPERIENCE
Over twelve years experience in Offshore and Onshore Oil & Gas and Marine Structure Development in National & International government projects. Project engineering management, Engineering, Design, Construction and Project cost estimation.

PROFESSIONAL EXPERIENCE

April 1993 – Present
Iran Marine Industrial Co. (SADRA)
Field Experience
* Site Supervision Engineering for ABOOMOSSA Jetties Project.
100 m quay wall for commercial propose and 120 m jetty for super heavy load and military services. (Piling, Sheet piling, Concrete and steel works)
Client: Iranian port and marine organization

* Site Engineering in south and north T-Jetty renovation – Oil terminal in KHARG ISLAND.
Salvage demolition and new structural installation. (Piling, Piping, Equipment, Steel fabrication and Installation)
Client: ETPM CO – NIOC - NIOPDC.

* Site Engineering for Sulfur Jetty renovation in KHARG Island
Installation sulfur conveyor and jetty extent ion, dolphin construction and fender installation.
Client: National Iranian Oil Co. (NIOC-NPC)

* Site Supervision Engineering for river protection MAROON – ESPHAHAN Pipeline.
River side protection by sheet piling and concrete caisson, construction the new oil compression station, modification the river direction. (Sheet piling, Earthwork, Concrete work and Piling works).
Client: National Iranian Oil Co. (NIOC-NIOPDC)

* Senior Installation Engineer for F9-A wellhead platform in Forozan oilfield – Persian Gulf.
Four piles with 55 m penetration, piling with diesel and heavy air steam hammer.
Pile drivability analysis and pile dynamic testing with PDA. Certified by DNV.
Client: National Iranian Oil Co. (NIOC- IOOC)

* Engineering Office Representative for AHWAZ Steel Bridge. KAROON River – South of Iran.
Three span arc suspension steel bridge (124m,248m,124m)
Construction quality control, pile dynamic testing with PDA, pile static testing, building pit construction, concrete work, dewatering and middle span installation. Certified by GL.
Client: Khozestan Steel Co.

Design Office Experience
* Design Engineer for 2000 ton Oil Terminal Loading Jetty – Boushehr – Persian Gulf
Deck & Pile system – Analysis & Design --Static and dynamic analysis -Ship impact and environmental loading -Pile drivability analysis
Client: National Iranian Oil Co. (NIOC-NITC)
* Design Engineer for 2000 ton Oil Terminal Loading Jetty – Neka – Caspian Sea
Deck & Pile system – Analysis & Design -Static and dynamic analysis -Ship impact and environmental loading -Pile drivability analysis
Client: National Iranian Oil Co. (NIOC-NITC)

* Senior Design Engineer for Extension Load out Jetty in Boushehr Offshore yard.
-Load out of AA, AC & AB Aboozar topside process platforms -Load out of LQ Living quarter topside platform. -Load out of AB & LQ jackets platform.
Deck & Pile system – Analysis & Design Static, PSI and dynamic analysis -Ship impact and environmental loading -Pile drivability analysis. -Load out simulation.
Design and Drawing certified by G.L.
Client: Iran Marine Industrial Co. (SADRA)

* Design Engineer for Load out jetty in SAFF yard in Bandar Abbass, Persian Gulf.
Load out of Sirri A & E topside and jacket platform. (Total – Serimer)
Deck & Pile system – Analysis & Design Static, PSI and dynamic analysis -Ship impact and environmental loading -Pile drivability analysis. -Load out simulation.
Design and Drawing certified by G.L.
Client: Saff Co

* Senior Design Engineer for Heavy Platform Area in SAFF yard in Bandar Abbass, Persian Gulf.
Load out of living quarter for south Pars Gas Development – Phase 1
Deck & Pile system – Analysis & Design Static, PSI and dynamic analysis -Ship impact and environmental loading -Pile drivability analysis. -Load out simulation. -Liquefaction analysis
Design and Drawing certified by G.L.
Client: Saff Co.

* Senior Design Engineering for Sadra Island Offshore Yard.
Yard layout arrangement for jacket (up to 3500 ton) and topside ( up to 10000 ton) construction. -Reclamation, piling and testing, pavement, warehouse, shops, roads, wharf, jetties, skid ways, railing road, electrical, communication, piping, offices and in fractural structures.
-Geo-technical engineering -Structural analysis and design -Pile testing (Dynamic & Static) -Load out simulation -Marine engineering -Detail drawings / Construction drawing -Construction quality control
SPD1 jacket (2400 ton) construction and load out. South Pars Gas Field - Iran
SPP1 topside (6900 ton) construction and load out. South Pars Gas Field - Iran
Certified calculation analysis for marine surveyor by G.L.
Client: Iran Marine Industrial Co. (SADRA)

* Senior Architectural Engineering for South Pars Gas Field Development project – in Technip Malaysia - SADRA- SAMSUNG Consortium. Fourteen months
Detail design activities in Architectural, Safety and Structural sectors. Procurement engineering for offshore architectural items.
SPP1, SPQ1, SPD1 and SPD2 topsides
Client: Pars Oil & GAS Co. (P.O.G.C. –NIOC).

* Structural Design engineer for South Pars Gas Field Development – Phase -1 – Preliminary design work
SPF1, SPF2 & SPP1 jackets
-In place analysis with considering dynamic effect of wave -Fatigue analysis -Dynamic Analysis and Calculating Inertia load set. -Floatation and Upending analysis -Load out analysis -Lifting analysis
-Pile drivability analysis
Client: Pars Oil & GAS Co. (P.O.G.C. –NIOC).

* Senior Engineering for preparation of Load out Procedure/Manual in South Pars Gas Field Development – Phase 1
SPP1 topside (6994 kn), to FLB 124 barge with push pull system. Approved by marine surveyor (Nobel Denton).
SPQ1 topside (4000 kn), to FLB 124 barge with push pull system. Approved by marine surveyor (Mathieu's – Daniel)
-Integrity topside structure during load out -Yard & Barge skid beam control -Sliding surface controlling (wood, Teflon, grease) -Push/Pull system, guider and connections -barge ballasting, tide effect and preparation of load out operation manual -Mooring analyses and mooring arrangement -Engineering Supporting during load out operation. -Load out supervisor
Client: P.O.G.C - PETROPARS (NIOC)

* Senior Design Engineering for Load out, Lifting and Float over of Sea water Intake Platform in Sirri Island - Sirri A & E Project.
Design review and procedure preparation for load out, transportation and float over of SWIP. Approved by TOTAL FINA ELF
-Ballasting analysis -Lifting analysis -Load out analysis -Sea fastening analysis -Pile dynamic testing
Engineering representative during load out, transportation, piling, barge positioning & installation.
Certified by B.V.
Client: SAFF Co. – TMSI. CO.

* Senior Field Engineering for float over of SPP1 topside in South Pars Gas Field Development – Phase 1
Installation of SPP1 topside by float over method. Document review, comments and Marine operation including sea fastening, transportation, entrance conditions, installation procedures and existing.
Design engineering has been performed by Aker Co. Approved by marine surveyor (Nobel Denton).
Client: P.O.G.C - PETROPARS (NIOC)

* Pile Drivability Analysis for following Projects:
1- Noshaher Port Jetty Client: Ports and Shipping Org. of Iran
2- Foundation of Ammonia Reservoir Client: RAZI Petrochemical Co.
3- ABOOZAR AB & LQ Jackets. Client: IOEC - NIOC
4- F9A Wellhead Platform Jacket Client: IOOC - NIOC
5- Ahwaz Sixth Bridge Client: Khozestan Steel Co.
6- Sadra island Offshore Yard Client: Iran Marine Industrial Co.
7- Sadra Boushehr Yard. Client: Iran Marine Industrial Co.
8- Boushe hr Dry Dock Client: Iran Marine Industrial Co.
9- Drood Cluster Project – Kharg Island Client: Total FIna Elf
10- Oroomieh Lake Bridge. Client: Road & Transportation Ministry
11- Mobin Sea Water Intake and Cooling System. Client: Mobin Petrochem. Co. NIOC

* Concrete Pile Integrity Testing and Reports.
1- Foundation of Ammonia Reservoir Client: RAZI Petrochemical Co.
2- Boushehr Heavy Navy Port. Client: Omran Shahel Co.
3- Shirin Shaher Bridge Client: Kandowan Co.
4- ISOICO Heavy Load out Jetty Client: Kandowan Co.
5- Basaeido – Qeshem Fishing Jetty Client: Karan Darya Co.
6- Noshar fourteen Story Building. Client: Central Saba Co

* Tender Engineering for Oil & Gas and Infrastructures projects.
-Preparation Technical Documents -Material Take off. -Requisition Document -Project Cost Estimate -Construction Method Statement. -Basic Design Endorsement. -Assessment of Consulting Engineering

1- South Pars Gas Field – Phase 1 (topside and facilities) International Tender, Client: Petropars - NIOC
2- South Pars Gas Field - Phase 4, 5 (topside and facilities) International Tender, Client: Petropars - NIOC
3- Kharg Island Gas Gathering - Phase 1 (Pipeline for gas gathering) International Tender, Client: IOOC – NIOC On Progress
4- Kharg Island Gas Gathering - Phase 2 (Offshore facilities for gas transferring) International Tender, Client: IOOC – NIOC On Progress
5- Kharg Island Gas Gathering - Phase 3 (NGL plant and marine export facilities). International Tender, Client: IOOC – NIOC On Progress
6- Sirri Island Gas Gathering - Phase 1 (Pipeline for gas gathering) International Tender, Client: IOOC – NIOC On progress
7- Sirri Island Gas Gathering Phase 2&3 (Offshore facilities for gas transferring) International Tender, Client: IOOC – NIOC On Progress
8- Salman Oil Field - Phase 2 (Offshore Facilities including Gas lift, Living quarter, Process and Riser platforms). International Tender, Client: Petroiran- NIOC On Progress
9- Salman Oil Field - Phase 3 (Pipeline for Gas & Oil transferring). International Tender, Client: Petroiran- NIOC On Progress
10- MOBIN Sea Water Intake & Cooling Water System. (Intake Culvert, Basin, Equipments & Pipeline for Sea Water Distribution) International Tender, Client: Mobin Petrochemical Co. –NPC - NIOC
11- Oromieh Lake Bridge (1450 m & 500m bridge span with special soil specification) International Tender, Client: Road & transportation Ministry

* Recently Responsibilities
* Senior Engineering for preparation of Bridges Load out, Transportation and Installation Procedure/Manual in South Pars Gas Field Development – Phase 1
SPB1, SPB2, SPB3 and SPB4 bridges (50m - 1650kn, 40m - 1300kn, 90m -2300kn, 120m - 3250kn respectively)
Very complicated arrangement and sea fastening on FLB 124.
Lifting and installation by two crane with very special condition
Approved by marine surveyor (GL).
Client: P.O.G.C - PETROPARS (NIOC)

* Senior Engineering for preparation of Load out Procedure/Manual in South Pars Gas Field Development – Phase 4/5
SPD5 / SPD6 topsides (each one 22200 kn) by push pull system, ISP / FSP Jackets (four tripod Jackets each one 4500 kn), Bridge and Flare support (4 decks each one 1500 kn) by lifting method and Bridges (4 bridges each one 1600 kn) by lifting method.
-Integrity topside structure during load out -Yard & Barge skid beam control. - Design of skid shoes -Sliding surface controlling (wood, Teflon, grease) -Push/Pull system, guider and connections -barge ballasting, tide effect and preparation of load out operation manual -weighing procedure -Mooring analyses and mooring arrangement -Engineering Supporting during load out operation. -Load out supervisor
Approved by marine surveyor (GL).
Client: AGIP - PETROPARS (NIOC)

* Senior Engineering for preparation of Load out Procedure/Manual in South Pars Gas Field Development – Phase 6/7/8
Preliminary study

* Design Engineer in Oromieh Lake Bridge in Structural and geotechnical section, engineering challenge with special conditions in that area. Marine Installation and new technique in bridge installation.
Client: Road & transportation Ministry

. Design engineer in Mobin Petrochemical in marine engineering section.
120 m pre-stress Concrete culverts with 9000 ton weight - Load out, Construction in Dry Dock- Transportation by floatation method and Installation by winches procedures and review analysis
22m pre-cast concrete culverts with 2400 ton weight, Construction in yard, load out by push pull system and installation by lifting crane barge.
Client: N.P.C – MOBIN PETROCHEMICAL Co.(NIOC)

March 1990 – March 1992
Military Services – Ahwaz City
Civil / Structural Engineering in the Military Project: -Fuel Pump station -Cinema Saloon -Ice Factory -Roads and Pavement

September 1990 – March 1990
Iran Fishing Co. (South Part)
Construction Engineering for Breakwater and Fishing warehouse.

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 6351 to 6400 of 15344)

Go to Search Parameters...

Brief Description

I am I have worked extensively on both land and offshore rigs. I always try to perform my job to the best of my ability, with safety to personnel as my #1 goal.

Water industry: French citizen w/U.S. Green card; 27+ years experience in construction & operations and maintenance; electromechanical and site management skills; specialist in process component for W/WW systems

I had more than 20 years experience in Gas Processing plant, previous company I worked for LNG Plant and last position as Utilities Senior Operator and Present company I have been working for Gas Processing as field operator.

Resume CV: To join an offshore drilling company as Rad. operator, Logistics Coordinator any place in the world

I would prefer to work as Commissioning Supervisor in the Middle East.

Objective Production engineer, oilfield engineer, or mechanical engineer in a contracting firm.

Dear Sirs, I am 33 yrs. old, from Romania, Electrical Engineer. I would like to get a job in electrical/administrative petroleum/oil/gas field. Even I've have a Diploma in Electrical field I can accept to work as electrician, technician, foreman, or engineer.

20 years experience in non-destructive testing and inspection as a technician, radiation safety officer, division manager, and project manager.

NACE Certified Coating Inspector #7278, with +20 years of experience, available as (3rd party) Q.A./Q.C. coating inspector, coating surveyor, coating supervisor, vendor surveillance, etc.

I have been working in the Construction Industry for 40 years at all levels up to Construction Manager. I have extensive experience overseas including Africa and Asia. I am looking for similar work and am prepared to work anywhere at immediate notice.

Maintenance of: - Simovert - frequency regulation for the speed control of High Power asynchronous motors 450 KW and 110 KW - Frequency regulation for the speed control of Low Power asynchronous motors - High Voltage switchgear equipments - MCC - Switchgear equipments - Low Voltage -ETC...

I 'm Canadian citizen, I have second class marine engineer.

25 years of experience all over the world in the instrumentation field including 12 years offshore oil platforms, erecting, construction, precommissioning , commissioning and start-up a wide range of pneumatic, hydraulic and electronic instruments, DCS – ESD – F&G systems.

Process Engineer

I accumulated 22 years of experience in the oil industry, most of the time with the Schlumberger service company in the area of Oilfield Services management, Reservoir Evaluation Wire line and Testing.

I have 21 years in Aust Army as Maint Planner/Supervisor with Diploma Engineering (Maint). Experienced trainer in Mincom Logistics computer systems. Willing to relocate nationally or internationally for the right position.

Over twelve years experience in Offshore and Onshore Oil & Gas and Marine Structure Development in National & International government projects. Project engineering management, Engineering, Design, Construction and Project cost estimation.

WORK EXPERIENCE I have 14 years of experience in plant F.C.C ( Fluid Catalic Craking ).Refinery El Palito in Venezuela ( PDVSA ) and experience in Pre commissioning

Over 25 years of exploration drilling and mining experience. Responsible for the coordination of drilling projects in both domestic and international environments.

I was employed by ARCO Indonesia Oil & Gas since April 1980 thru March 1999. My last position was Elect/Instr Supervisor of NGL gas plant refinery located at NorthWest Java sea, for offshore facilities. My current employer is BP-Indonesia, position job as Maintenance Planner.

26 years Mechnical Design Engineering 16 years CAD experience including intensive 3D modeling 14 years product design experience. 12 years manufacturing tooling and facilities experience.

23 years experience in the Electrical Distribution/Electrical Contractor Industry. Wish to acquire a part time or full time position in an office or job site environment.

Job objective: General Supervisor, Field Supervisor, Project Manager or Assistant Project Manager. Interested in overseas opportunities.

Objective: Seeking a career position with a progressive organization where my skills , training and extensive knowledge and experience can be fully utilize, while offering the opportunity for continued career growth.

Highly experienced purchasing and material management professional. Specialized experience in remote, severe climatic locations. Extensive experience in cross cultural work situations.

Curriculum Vitae „h Over 25 years of oilfield experience in Canada „h Mechanic on a seismic crew until tools were stolen „h Roughneck to driller, 11 years as a driller on a drilling rig „h Owner/operator of a vacuum truck business „h Mechanically inclined

BS EE from USA. I have over 14 years of experience in maintenance and projects while working with reputable organization like Exxon, Mobil, Occidental and BP Pakistan in fertilizer, petrochemical and oil/gas E&P industries.

OVER THIRTY YEARS EXPERIENCE AS A FULLY CODED WELDER ALONG WITH FOREMAN, SUPERVISER AND WELDING ENGINEER/CHIEF WELDING ENGINEER POSITONS ALSO UNDERTAKEN ALONG WITH NORMAL WELDER POSITION.

Seeking employment where my years of experience in surface & underground mining & construction, as well as my strong sales, contracting, consulting, and management skills can best be used

Chemical engineer w/ experience in developing various contracts in oil, gas, water, waste treatment & soil road maintenance. Expert w/ performance based contract. Possesses good organizational, team & interpersonal skills. Adept at working & communicating across disciplines & management levels.

Looking for a new challenge at the end of 2003 my present contract end then

Operate, commission and monitor equipment in assigned areas, maintaining parameters with the guide lines of the operating manuals and procedures of 80,000BPD three phase separation multi train crude separation units, 110 MMSCFDgas compression& treatment plants

Strategic Planning Business Development Project and Business Valuation

I’m an international Petroleum Engineer, currently working in Turkish Petroleum Int.Co.Ltd. as a Completion/Workover Supervisor back to back Ankara/TR to Aktjubinsk/KZ, experienced about 20 years on land and offshore, in offices in many companies and projects.

Nobody has climbed up through the steps of success with his hands in his pockets.

Seeking challenging assignments in the field of Process Engineering Design, Simulation and Commissioning with leading organisations of repute in the Petrochemical Industry that offers me opportunities to utilize my engineering skills & experiences for advancement in my career endeavours

I have BSc. in Mechanical Engineering, MSc. in Mechanical Vibration of Rotating and MSc. in design of gas turbines. I have >20years of experience with Engineering and Operating Companies in O&G and Petrochemical fields as Senior Mechanical Engineer in Egypt Enppi and in Qatar QP Offshore and QVC

C/C++/ VB / SCADA / Electronic / Embedded / Automation / Systems Engineering

I completed my degree in Electrical Engineering and had taken and passed the highest National Examination in The Philippines, Professional Electrical Engineers Examinations in 1986. I have a good experience in Oil and Gas, Controls, Fire and Gas Systems, Design, Detailed Autocad Drafting(Isometric),

Instrument Engineer is seeking a challenging Position for growth and career opportunity in Oil & Gas Industry. More than 13 years of experience in Preventive and break down maintenance for power plant & gas plant instrumentations with GE Frame 6 gas turbines, DCS and Mark V control systems.

Associate Degree in Mechanical Engineering Draughting, 10 years Experience in various Mechanical and Plant Layout applications, using Inventor, Autocad, Pro Engineer, MSC Patran. Heavy Engineering Environment, International Earth Moving Machinery Manufacturing Company in South Africa.

BE Mechanical Engineer with 5 years experience in Piping Stress Analysis

Experienced exploration / production geophysicist and geologist with major Exploration Companies

22 years oil field Experians. Higher secondary.

Over 23 yrs of heavy earth field mechanic. AAS in Heavy equipment and diesel Technology. Lack final semester for BA in Training Industry & Business. CAT and Kamatsu trained.

AutoCAD, PDS (3-D modeling). Lead engineer of erection department

I hold a degree in Polymer Eng. from the Federal University of Technology Owerri, Nigeria. I am proficient in Autocad 2D/3D modelling, HYSYS, Bentley Auto Plant/P&ID, Boiler Maker, Autodesk Inventor

HIGHLY COMPETENT IN BUILDING AND ROAD CONSTRUCTION WORK(B.ENGINEERING,CIVIL)

Instrumentation technician with nine years experience in maintenence,repair,calibrating and installing of electrical,electronic and pnuematic equipment.

Mechanical Engineer with manufacturing experience

First Prev 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 [ 128 ] 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 Next Last

Seach Parameters


Goto Advanced Search...
Keywords: (e.g. mining engineer)		Find results with:

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out