Resume - EEHA and Hazardous Area Expert - Seeking FIFO

Misco Jobs

Resume #78627

CONTACT INFORMATION:
View contact information...

Present Position and Employer
* Owner/Operator – EPEE Consulting Pty Ltd

Years Experience
* 30 years in all – 20 years experience with Hazardous Locations equipment (16 as an engineer)

Qualifications and Certificates
* Bachelor of Engineering (Electrical and Computer Eng) QUT; 1992
* Associate Diploma of Electrical Engineering USQ (formerly DDIAE); 1986
* AS/NZS 4761.1 EEHA Competencies: 010, 012, 107, 214, 215, 408, 407, 409, 410, 610, 705, 706, 707
* DEIR (Qld) Accredited Hazardous Areas Auditor (No. 02/0093) Category 3: Zones 0, 1, 2, 20, 21, 22
* Queensland BLUE CARD holder (construction industries)
* Quality System Auditor (training via NATA and SAI Global)

Professional Societies
* Member – Engineers Australia
* Member - Standards Australia – (EL-014; EL-023 & MS-011)
* Member - Metrology Society of Australia
* Past Member - International Electro-technical Commission (IEC)

Skills
* EEHA Inspection Team Leader & QC Documentor
* Design, Inspect and Remediate Electrical Equipment in Hazardous Areas (EEHA) installations,
* Hazardous Area Classification (HAC) studies and remediation for gas, vapour and dust hazards,
* Compile Hazardous Area Verification Dossiers (HAVD),
* Verify new and modified EEHA designs,
* Perform conformity assessments on non-AUS Ex / ANZEx certified product to Australian standards and publish Conformity Assessments,
* Compile inter-comparisons between foreign and national standards on a clause by clause basis,
* Investigations into failures of HV and MV electrical equipment including of mine power systems, cabling and protection relays (U/G and surface),
* HAZOP and Risk Analysis,
* AS 4114 spray paint booth installation and design inspections and remediation,
* AS 1940 assessment of combustible and flammable liquid storage and remediation,
* AS 4289 assessment of acetylene and oxygen storage and installations and remediation,
* AS 4332 assessment of gas cylinder storage facilities and remediation,
* AS 2022 assessment of anhydrous ammonia storage facilities (water treatment and nitrates plant),
* AS 2927 assessment of liquefied chlorine gas storage and installation (water treatment),
* Devise and cost engineering proposals to conduct HAC studies and EEHA inspections,
* Write papers on EEHA topics for technical journals and present papers at conferences,
* Attend and contribute to Standards Australia MS-011, EL-014 and EL-023 subcommittees and disseminate information from these committees to relevant staff,
* Liaise with clients and engage in business development by seeking new clients,
* Attract new staff for positions that may occur on a temporary or permanent basis,
* Training Material Author, Presenter and Assessor for MOXI (http://www.moxi.com.au/Home/Trainers_assessros.htm ).

Employment History
* EPEE Consulting – Sole Trader (see separate document listing services)
* SAI Global Pty Ltd – Quality Systems and EEHA Overhaul and Repair Workshop Auditor
* Ninness Consulting Pty Ltd; August 2007 to September 2007 – EEHA and HAC projects
* HAZEX Pty Ltd; May 2006 to April 2007 ( working for HATCH) – EEHA inspections and rectifications
* INETE Pty Ltd; April; 2007 to September 2007 – dragline overhaul and repair & EEHA and HAC projects
* PCT Engineers Pty Ltd, Brisbane; Jun 2004 to April 2007 – EEHA inspections, design & HAC projects
* VMS International Pty Ltd; RAAF Amberley ; Feb 2002 – Jun 2004 – Lab Manager – instrument calibration
* Department of Defence (Civilian) - RAAF (DGTA-NDTSL); RAAF Amberley; May 2000 – Feb 2002 – NDT Eng.
* Electrical Testing and Certification Centre (SIMTARS); Feb 1990 – May 2000 – EEHA Assess. & Certification
* Department of Defence – Army (RAEME); Various Sites; Aug 81 – Feb 1990 – Instrument/Electronics Technician

Other Training:
* Lead External Auditor – SAI Global (ISO 9001)
* Dale Carnegie Leadership Training for Managers
* National Restricted Electrician's License (NREL – TAFE)
* Level 2 Non-destructive testing (Radiography, Ultrasonics, Eddy Current only)
* EMC Pre-compliance Testing - AEDC
* Internal Laboratory Auditor & Quality Management in the Laboratory – NATA (ISO 17025)
* Radio Tradesman - Commonwealth Trades (includes RAAF calibration technician training)

Notifications:
* Current Standards Australia committee member (MS-011, EL-014 and EL-023),
* Previously NATA signatory at VMS International Pty Ltd (1.41 Pressure and Vacuum),
* Previously NATA signatory at SIMTARS (3.80 – Electrical Testing & 3.90 - Hazardous Location Testing, also signatory for other various tests and Inspection),
* Former IEC committee member (Technical Subcommittees 31J and 31H).

Papers Presented:
* "EEHA Installations and the Queensland Electrical Safety Act and Regulation" – IDC Conference, Townsville, September 2008
* "Introduction to Hazardous Location Protection Techniques – Part 1: Gases and Vapours" - Institution of Engineers Journal – May 2005,
* "EEHA – Changes in the Air" – published in the Journal of the National Safety Council of Australia, Mar 2005,
* "Uncertainty & Measurement for NDT Test Equipment" (NDT Conference – RAAF Amberley, Nov 2001).
* "Intrinsic Safety and Non-destructive Test Equipment" (NDT Conference – RAAF Amberley, Nov 2000),
* "Intrinsic Safety in the Offshore Petroleum Industry"(Offshore Petroleum Communications conference - Perth, 15,16 Jul 1998)
* "Intrinsic Safety Considerations in Communication Equipment for use in Underground Coal Mines"(Underground Mine Communications conference - Darling Harbour, Sydney:11,12 Dec 1997),

Research Projects:
* Characterisation testing of IEC breathing and draining device test apparatus (now in AS/NZS 60079.1),
* Gained ACARP research grant for High Current I.S. Spark Test Apparatus,
* Temperature rise testing of dust laden junction boxes at various dust thicknesses,
* Assisted research engineers with ACARP Arc Fault Containment and Mine Power Supply Transient research.

Site Visits and Technical Audits:
* 2009; EEHA Inspection Supervisor of Santos Gas Compressor Stations – CS3 and PCS (Western Queensland)
* 2008; Revision of training material for MOXI (www.moxi.com.au)
* 2008; Hazardous area classification reviews of marine tankers – Coogee Resources
* 2008; Hazardous area classification of methane drainage systems in landfills – various clients (inc Mono Pumps)
* 2008; Conformity assessments of foreign certified EEHA – various clients
* 2008; Various hazardous area classifications for Aquatec Maxcon – for water recycling plants
* 2008; Hazardous area classification of plant at NYRSTAR Zinc Refinery, Hobart
* 2008;.Hazardous area classification of ammoniation plant for BCAA at Bribie Island
* 2008; Various EEHA installation inspections for Fuel Flow in South East Queensland (Service Station Installations)
* 2007; Presentation of EEHA courses for MOXI (www.moxi.com.au)
* 2007; Hazardous area classification of methane releases from Brisbane City Council Landfill Site – Nudgee Beach
* 2007;.Hazardous area classification and equipment design advice for ammoniation plant in North Brisbane – Ninness Consulting
* 2007; Various conformity assessments of foreign certified explosion protected apparatus – HAZEX Pty Ltd
* 2007; Yabulu Nickel Refinery, Townsville – EEHA Audit and remediation & redesign of aspects of the upgraded installation – HATCH Engineering
* 2007; Tarong Power Station, Nanango – HAC study and EEHA inspection of generator hydrogen system,
* 2007; Kogan Creek Power Station, Queensland – EEHA inspection and report on Coal Handling Plant,
* 2007; QNP Moura QLD – Conformity Assessment of foreign certified EEHA to Australian standards.
* 2006; QNP Moura QLD – EEHA reinspection of QNP-Nobel ammonium nitrate plant,
* 2006; Brisbane Water - Mt Crosby & North Pine, Brisbane – HAC study of water treatment plants,
* 2006; CCI Newcastle NSW – HAC and EEHA inspection of coal analysis laboratory,
* 2006; Goodman Fielder Waygunyah NSW – HAC study and EEHA inspection of oats processing plant,
* 2005/2006; Tarong Power Station, Nanango QLD – HAC study and EEHA inspection of flammable store, gas turbine and related fuel systems,
* 2005; Tarong Power Station, Nanango QLD – HAC study and EEHA inspection of coal handling and fuel oil facilities at Tarong Power Station,
* 2005; QNP Moura QLD – EEHA reinspection of ammonium nitrate plant,
* 2005; Tarong Power Station, Nanango QLD – HAC study and EEHA inspection of hydrogen generation system,
* 2005; Iluka Geraldton WA – HAC study and EEHA inspection of Narngulu synthetic rutile plant,
* 2005; Laminex Perth WA – Final HAC and EEHA inspection of MDF Plant (combustible dusts),
* 2004; Port Headland/Telfer WA – EEHA inspections of gas power station, piping & compressor stations,
* 2004; Laminex Perth, WA – Initial HAC study and EEHA inspection of MDF Plant (combustible dusts),
* 1997; Taupo, New Zealand - Geothermal Power Station EEHA Inspection and Conformity Assessments,
* 1995; Tahmoor Colliery, Tahmoor, NSW – Inspection of Underground Coal Mines Ex v control room,
* 1994; Joy Manufacturing Moss Vale, NSW – Assist with the development of an Ex v underground control room,
* 1993; Ampol Refinery, Fisherman's Island, Brisbane – EEHA inspection of analyser houses,
* 1992; Nowra, NSW, Australia – EEHA inspection of Ex v control rooms in ethanol plant.

View contact information...

«« previous resume

next resume »»

Search Results (Resumes 751 to 800 of 15509)

Go to Search Parameters...

Brief Description

Over 33 years of working experience within India and abroad as electrical superor, senior electrical foreman, commissioning engineer, Elelectrical specialist.and Specialist Consultant.All the 33 years Maintenance ,Commissioning and Consultant for CMMS and Mtc Optimation Projects in oil,power Indys.

Posses degree in Geology. Familiar with Microsoft Work, Excel, Power Point, Project , Landmark Geosciences Workstation(Good), Petrel (Good), Well Kill Sheet Program(Good), Drill bit hydraulic software(very good), Mud logging software setup(good) and trouble shooting.

Chemical engineer with twenty four years of total experience in the Oil & Gas, Oil Processing and Petrochemical industries. I have rich experience in project engineering, design supervision, multi-discipline engineering co-ordination, contract management, commissioning supervision and construction

Mud engineer with 24 years of experience, on land and off shore, made all types of mud, OBM, SBM and WBM

Twenty-Seven years work experience primarily in Mechanical, Process Piping Design, Civil/GIS, CADD (Computer Aided Design Drafting) and CADD Management. Broad based as well as extensive expertise in Engineering Applications and Software Systems.

I am graduated from Algerian Petroleum Institute as an Enginer in petroleum geology (5 years graduation). I was involved in geological interpretation for prospect generation from 1995 to 2000, since then I have been focusing in geochemistry and basin modelling (1D, 2D and 3D) regional studies.

PROJECT MANAGEMENT

Quality, Health, Safety and Environment Manager - Offshore and Onshore

Free! Background and extensive experience in HES regulatory requirements through all stages of execution in major capital projects including Concept Design, FEED, Detailed Design, Construction / Fabrication and Hookup and Commissioning. Have 28 years of experience in the oil and gas industry which also i

Supply Chain and Procurement Management

Well Test Engineer

Experienced in Structural Steel Detailing. Highly proficient in AutoCAD, Capable to produce quality Erection plans and Shop Drawings.

I have over 20 years of specialised experience with varied role players such as Consultant, Contractor and client in the area of Project Control & Management. My experiences cover full range of services on the following categories • Business Process Engineering and Re-Engineering • Business Automat

Experienced CAD Technician with an excellent work ethic; loyal, and a team player.

Experienced Professional Mechanical Engineer with 17 years diverse professional experience in Oil & Gas Industry - Project/Design/Operations Engineering, Rotating & Static Equipment sizing and selection, Commissioning Activities, and associated technical skills.

Environmental monitoring

Reliable and dependable

Instrument engineer supervisor material control supervisor

Individual expert in Surveying - Topography - Land registration - Remote sensing – GPS – Cartography - GIS agreed by the European Commission

Visual Foxpro RDBMS Programmer LAN Environment / Technician / CAD 3D Designer

Resource and Evaluation Specialist, MSC Geology, 15Years experience, Specialize in Platinum Industry

I am a Civil Engineer, Internal Auditor & shortly being certified as Lead Auditor by IRCA.

Results-driven manager in diverse supply chain, purchasing and sourcing areas.

Well Integrity Specialist, Completion Production Engineer

I offer many years of experience in the Petroleum Reservoir Engineering field. I have expertise in reservoir engineering management and consulting, reservoir integrated studies, well testing/pressure transient analysis and decline curve analysis

Oil Industry exp: 28 YRS, CITGO/Consulting Downstream/Upstream/Latin America/Pricing. Objective: Pricing Manager, Business Development Manager, Head Economics Dept., Refining(Tech/Fin), E&P(Fin)Invest. Bank.

1st class Mechanical Engineer from reputed Institution, preferably specialization in Thermal Power Plant, having PG Diploma in Thermal Power Plant Engineering from National Power Training Institute, Neyveli Lignite Corporation, TamilNadu.

EEHA and Hazardous Area Expert - Seeking FIFO - Remote Area Work

Administrative and Technical support Telecom, Electrical, Electronics and Instrumentation professional with 19 years of experience in India & Abroad, fast-paced environments demanding strong organizational, technical and interpersonal skills

Engineering Graduate with 19 years of experience in Sales & Marketing, Business Development, Operations, Supply and Distribution / Logistics, P&L Management of businesses involving Lubricants / Petroleum / Coatings offering Value added Solutions in Industrial, Power, Marine Segments

BE Mech. API-653/510/571 certified. 16+ years inspection experiance

15+ years of various jobs with Foxboro DCS, and Triconex IPS/FGS Systems

24 years in the mining industry, both in Australia and as an expat, started as a labourer, and worked my way to top management positions.

I am a highly skilled Mechanical Engineer with over 18 years of experience in engineering (oilfield equipment, rotating equipment, wind energy) and general technology with PhD in Mechanical Engineering.

I senior completion and workover engineer 19 yeas experience

To further enhance career growth and inter-personal skills, To share technical knowledge with other colleagues, To take the challenge of having a wider responsibilities within a new organization.

An Oil & Gas Professional with 30+ years experience in all facets of Drilling and Completion

ISO 9000:2000 QMS-03 Lead Auditor IRCA Course No.17047 and Internal Quality Auditor (IRCA No. R141), Senior QA/QC Engineer, Certified Welding Inspector (CSWIP3.1), SNT-TC1A Level 2 for RT film interpretation / UT / PT and MPI, Piping, Blasting/Painting, Structural & Pressure Vessel Inspector. Expert

An experienced Project Engineer - Designer - CAD Manager with very strong concepting /training/team building skills

Resourceful Project Superintendent and QA Supervisor with expertise in oil and gas industry project installations and industrial construction; focused on positively impacting cost control, resource maximization, timeline management, and team performance.

Over 25 years in the Construction Field

Rigging & Lifting Supervisor, Health & Safety Advisor, looking for work in the construction industry, freelance contractor

A good candidate for Mill Superintendent, Mill General Foreman, Mine or Mill Supervior, Mill Trainer or Environment coordinator. 25 yrs experience in Copper, Nickel, Gold, Zinc, Lead, Silver, Palladium, Platinum, Potash mines.

I've experienced for the boiler and energy sectors, in the commercial management and the site execution.

Detail oriented leader with over 25 years in the industry. Motivated leader and trainer. Work well with multinational teams

I am a Petroleum Engineering Technologist with 29 yrs E&P experience, the last 12 yrs have been with major Operating Companies in positions of; Lead UBD Engineer, UBD Project Manager, UBD Advisor and Drilling Supervisor. Available for a new project 30 Novembewr 2009.

20+ years piping field - 13+ years PDS

INSTRUMENT AND CONTROL ENGINEER, DCS SYSTEM AND CONVENTIONAL SYSTEMS EXPERIENCE.

22 years oilfield experience. High pressure, horizontal pumpdown experience. Experience with both Open Hole and Cased Hole Logging and Perforating. 2.5 years overseas.

ISO 9000, ISO 14001, OHSAS 18001, ISO/TS 16949, TQM, SAP R3, FOURTH SHIFT, SPC

First 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 [ 16 ] 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Next Last

Seach Parameters


Goto Advanced Search...
Keywords: (e.g. mining engineer)		Find results with:

Frequently Asked Questions

What's the most effective way to perform a search?
Go to Advanced Search
1. Select 'Industries', 'Categories', 'Education', and 'Experience' fields. Click 'Search' and look through results.
2. Enter one or two of the most important keywords. Click 'Search' and look through results.
3. To search within results add more keywords.

How can I find resumes that contain specific exact phrase?
To search for an exact phrase, just put quotation marks around two or more words, for example "mining engineer". Use this feature to narrow your results or to find words that can be typed differently, for example AutoCAD "Auto CAD".

More Frequenly Asked Questions...

Employer's Center

» Employers Home

» Feedback

» Help

» Post Jobs

» Edit/Delete Jobs

» Search Resumes

» Resumes By Email

» My Account

» Log In

» Log Out