Position Applied For:

Instrument Technician (first choice)
Instrument Fitter (second choice)

Educational Attainment

Year School Course

1971 — 1976 San Vicente Elem. School Primary Education
1976 — 1980 San Vicente Parochial School Secondary Education
1982 — 1983 Samson Institute of Technology Refrigeration and Air Conditioning

Industrial Training Courses

• Instrumentation and Control Certification Review
• Basic Fire Fighting and Sea Survival
• H2S Awareness
• Permit Holder/Applicant
• Job Hazard Analysis (JHA)
• Total Process Reliability (TPR)
• Root Cause Analysis (RCA)
• Basic Offshore Safety Induction and Emergency Training (BOSIET)
• Helicopter Underwater Escape Training (HUET)

Certification

Certified Instrumentation and Control Engineer No. 0350 by Philippine Instrumentation and
Control Society.

Qualification Highlights

With seventeen years work experience in Oil and Gas instrumentation distinctively for maintenance,
Construction and commissioning of Gas Fractionation Plant, Oil Refinery, Oil Gathering Station and (FPSO) Floating Production Station and Offloading Facilities.

Work Experiences

Work Location: Shell Nigeria Bonga FPSO (Offshore commissioning)
Nature of Business: Oil and Gas Production
Position: Instrument Technician (Pacific Ocean Manning Inc. / V- Offshore UK)
Period Covered: July 4, 2005 to October 1, 2005
Job Description:

• Involve in fire and gas loops functional testing of Solar Gas turbine water mist system and its associated shut down loops.
• Carried out wet testing of deluge system of every fire zones, test done based on cause and effect diagram by simulating confirmed fire detection signals to its associated fire and gas detectors/sensors and make sure that foam and water control valves are on correct position.
• Calibration and alignment of line of sight open path gas detector.
• Performed Pre Commissioning Procedure (PCP) Test of Fire and Gas loops.
• Carried out stainless steel tubing job for transmitter impulse lines, control valve pneumatic line, instrument air lines and others high pressure hydraulic lines and steam tracing line.

Work Location: Petroleum Development of Oman (Marmul site)
Nature of Business: OIL and Gas Separation and Production
Position: Instrument Technician (Sponsored by IPEDEX / AMEC)
Period Covered: December 10, 2000 to April 3, 2005
Job Description:

• Check and rectify trips and communication failure of different types of oil wells having beam pump, progressive cavity pump (PCP) and electrical submersible pump (ESP) Also check wells for correct discharge pressure trip point and well production analysis.

• Coordinates with local contractor for smooth implementation of awarded project and to ensure that everything conforms to client's standard and requirements.

• Check and rectify malfunction of vital equipment in oil production station which includes, three phases separator used as bulk or test. For test separator it is our responsibility to ensure the correct test result of each in every well under test using multiphase meter, ultrasonic interface level transmitter and positive displacement meter. Also involve in corrective and preventive maintenance of Hydro cyclone sand separation skid, Borsig reciprocating gas compressor and Shipping pump.

• Prepare all drawings and materials required for shut down and liaise with operation department before and during shut down to avoid any process disturbances and plant upset.

• Responsible for any stainless steel tubing job required for steam tracing, high pressure hydraulic line, instrument impulse line and other instrument fitting job.

Work Location: Occidental Petroleum of Oman (Safah Oil Field)
Nature of Business: Oil and Gas Separation and Production Plant
Position: Instrument Technician (Sponsored by IPEDEX / AMEC)
Period Covered: November 20, 1999 to December 18, 2000
Job Description:

• Review process flow diagram (PFD) piping and instrument drawing (P&ID) and logic diagram of new projects and recommend solution to any defects and upgrade documentations.
• Assist local contractor for commissioning and start up of completed equipment so as not to interrupt and avoid plant shut down during start up.

• Trouble shooting and rectifying vital equipment like 16-cylinders reciprocating Superior engine driven three stages gas compressors having altronic control circuit; 2-stages Solar Gas Turbine driven compressors; and 12-cylinders Waukesha and Caterpillar engines.

• Involved in Process Instrumentation, mainly for corrective maintenance and attending night call out duty for Instrument failures in Crude Distillation Tower, Crude and Diesel Heater, Oil Gas and Water Separator and Desolater.

• Involved in the ongoing DCS and PLC Control upgrading project to ensure all completed instrument loops are properly documented and operating as per process requirement.

Work Location: Unocal Pailin Offshore Gas Field, Thailand
Nature of Business: Oil and Gas Exploration and Production
Position: Instrument Technician (Sponsored by P. T. McDermott)
Period Covered: June 1998 to December 7, 1998
Job Description:

— Hook up and commissioning of Offshore Gas Production Platform
— Loop testing of serial link between equipment control panel and DCS.
— Performed functional checks of all instrument loops associated with propane compressor and CO2 removal skid.

Work Location: Total Bangkok Offshore Oil Field, Thailand
Nature of Business: Oil and Gas Exploration and Production
Position: Instrument Technician (Sponsored by IPEDEX Thailand)
Period Covered: April 8, 1998 to May 7, 1998
Job Description:

— Overhauling, calibration and loop checking of all instruments at WP-8 well head platform.
— Type of instruments maintained includes high pressure ITT Barton Recorders, Valtek and Fisher Control Valve, Masoneilan Level Trol and Controller

Work Location: Formosa Petrochemical Corporation, Taiwan
Nature of Business: Petrochemical Construction Project
Position: Instrumentation Foreman – June 25, 1997 to September 1, 1997
Instrument Supervisor – September 1, 1997 to January 27, 1998
(Sponsored by Samsung Engineering & Construction Co.)

Job Description:

• Supervised and demonstrate to all instrument fitter the correct way of bending stainless steel tube, proper usage of fittings and proper slope based on process requirement.
— Supervised the correct installation, location and specification of all instruments and vital equipments for correct functionality as per client's standard.

— Conduct safety meeting on a regular basis for all workers under my supervision for safe completion of project and make sure that everybody doing job safely.
— Checked and rectified any defect on instrument drawings such as instrument data sheet, piping and instrument diagram, instrument hook up drawing and instrument loop diagram.
— Coordinates with other department head that may be affected on implementation of instrumentation job and recommend acceptable solution to concerned department.

Work Location: Abu Dhabi Gas Industries GASCO, U. A. E.
Nature of Business: Natural Gas Liquid Fractionation Plant
Position: Instrument Technician (Sponsored by Euro Mechanical and Electrical Contractor)
Period Covered: May 8, 1990 to December 20 1995
Job Description:

— Carried out routine preventive maintenance on all instrument loops as per Preventive Maintenance Schedule.
— Involved in trouble shooting and rectifying erratic process parameter indications.
— Worked on vital equipment such as Rolls Royce and General Electric engine-driven gas compressors having Netcom 5000 Digital Control and Speedtronic Control Circuit.
— Functional testing of shut down loops associated with de-etherizers, de-botanizers, and de-propanizer12-passes furnaces.
— Attending night call out duty for malfunction of propane treater fractionation column, and feed surge drum.
— Carried out stainless steel tube bending and other related instrument fitting job that may be required for improvement of process measurement and control.

Work Location: KNPC Mina Ahmadi Oil Refinery, Kuwait
Nature of Business: Oil Refinery
Position: Instrument Technician (Sponsored by Kellogg Plant Services Inc)
Period Covered: January 1989 to March 1990
Job Description:

— Worked in Eocene and Bitumen Plant.
— Trouble shooting and rectifying abnormal level indication of Glycol-filled D. P. Type level transmitters.
— Field calibration of interface displacer type Masoneilan level transmitters.
— Calibration and stroke checking of split-range operated control valves.
— Functional testing of heater cascade control loop and its shut down system.

Work Location: KNPC Mina Abdullah Oil Refinery, Kuwait
Nature of Business: Oil Refinery
Position: Instrument Technician (Sponsored by Braun Transworld Corporation)
Period Covered: August 27, 1986 to August 13, 1988
Job Description:

— Involved in the construction and commissioning job.
— Instrument installation and bending of stainless steel tubing for transmitter impulse lines and air supply lines.
— Carried out calibration and functional check.
— Worked in Valve Repair Shop, mainly in overhauling, calibration and passing test of different types of control valves such as Orbit, Valtek, Fisher and Masoneillan.

Work Location: United Coconut Chemical, Batangas, Philippines
Position: Instrument Fitter
Company: Atlantic Gulf and Pacific (AG&P)
Period Covered: April 1984 to April 1986
Job Description:

— Performed bending of stainless steel tubing (with 6 mm. 10 mm, and 12 mm. OD.) to be used for transmitter impulse lines.
— Layout and installation of carbon steel small bore piping instrument air lines from instrument air header to instrument tapping point.
— Instrument loop check from field mounted instrument to main control room.

References:

Available upon request